Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

texturing question

Posts

texturing question

#1

texturing question

Carol Reed - Dubuque, IA (temporarily)

>This not for a turning but you folks seem to have more experience with it.

I want a textured line on a panel. Something in the neightborhood of 1/4 to 3/8 wide. My thought was to file a checkered pattern in the end of a piece of square stock and use it as a stamp. Will that work? Also, are the wood fibers crushed or cut? It seems to me the finish would 'take' differently. Which is sort of the point. My finish will be clear and I want the texturing detail to offer a hint of a design detail found in other furnishings in the same area. Oh, the wood is white oak, if that makes a difference.

Thanks for input. I have lots of flat woodworking expereince but I have never tried this before and it is for a client, so I can't mess it up. :-)

Re: texturing question

#2

Re: texturing question

Thom

>I just added texturing to a piece of maple (made into a bowl) using the Sorby Texturing tool.The bowl was drying so it had gone out of round. The texturing went on uneven and even caused some tear out so I used a small square faced hammer and whacked it until it looked like I wanted it to look. I have often wondered if those stamps that they use to mark metal would work. You know grind off the letters and numbers and make your own pattern. Whacking doesn't seem to mess up the fibres.

Re: texturing question

#3

Re: texturing question

John Lucas

>Carol i've done both. Leather tools make a good texture. When I made my first hand mirrors I used a nail set to stipple the background of a carved area. That looks really good.

A much faster way is to use a dremel engraver. Take a 1/8" drill bit and break it off or use a nail of the same size. Round over the tip and then use this to create a random pattern. If done right it gives a look like leather.

You can create a lot of different patterns using woodburning tools.

I also use a Dremel a lot with a little round ball cutter. I find the best look is to use 3 different sized ball cutters. I need to take a photo of my test boards to show you some of these techniques.

Re: texturing question

#4

Re: texturing question

Carole in VA

>John, do you use the ball cutters by Dremel or some other manufacturer? The ones I have that came with my Dremel are not worth a hoot. I was thinking about getting one of the diamond burr types.

Re: texturing question

#5

Re: texturing question

David Propst

>Hi Carol,

In Chris Pye's book Carving on Turning. he shows a stamp just like you describe. It is worth making one and testing it.

David

Re: texturing question

#6

Re: texturing question

John Lucas

>Carol The ones from Dremel don't last very long. They do cut pretty good at first. I have been using the ones I get from www.riogrande.com I hope that's the right URL, I order from their catalog instead of online. They have just about every cutter you could want for a rotatry tool. They also have the Foredom handpieces.

Re: texturing question

#7

Re: texturing question

Ed Kelle

>I have been using the diamond ones constantly. They sure do seem to last a long time. I've probably gotten over 80 hours use on the large ball.

I have seen someone (woodcraft?) also has a little more expensive set that was "industrial". Not sure what difference that makes.

They cut well but like to burn and clog up when hitting end grain. so what I just started doing is keeping a small film cannister of Simple Green next to me. When it clogs, I dip the tip on there while still running, then run it on one of those rubber sanding block cleaners.

The Simple green frees up the burned wood better than the sanding block alone.

Re: texturing question

#8

Re: texturing question

Ron Bauman

>Hey Carol,

I just recently purchased a rotary chisel from this co.http://www.rotarychisel.com/ It gives the effect of a chiseled surface. I got a RotoZip tool to run it in. Works good so far.

Re: texturing question

#9

Re: texturing question

Arch

>Carol, there is a technique for making texture stand proud of the surface that I have never tried, but maybe someone will jump in and explain if and how it works.

IIRC, equal depth shallow depressions are punched at random or in a pattern into the wood. Then the surrounding surfaces are sanded down level with the bottoms. When the surface is lightly wetted the depressed areas supposedly will expand above the surface. I have no idea if this works or even if it looks good.