Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

This is the most versatile work station you will ever use

Delta Lathe motor size

Posts

Delta Lathe motor size

#1

Delta Lathe motor size

kkamm

>Now that I am getting in to turning again, I once again get the sense my lathe is underpowered. I have a Delta, 12" variable speed where the variable speed part is controlled by turning a handle that then changes the diameter of one of the pulleys. If I recall, it has at most a one HP motor.

Given I have a little Christmas momeny, does anyone think it is worth upgrading this to say a two HP motor or do you think with this arrangement, I may not see any benefit due to belt slippage, etc.

Re: Delta Lathe motor size

#2

1 hp is plenty for a 12" lathe

T Daniel

>unless you were to use a coring tool but I can't see that being practical on a 12" lathe. I think I would spend the money for another gouge or chuck.

TD

Re: Delta Lathe motor size

#3

Delta Lathe motor size

DougJ in Crawfordsville, IN

>The Delta I use to have was a 14" and only had a 3/4 hp motor. It was quite enough for that lathe, unless I tried to horse out a bigger cut than I should.

Are you experiencing some stalling in the turning while making cuts? If so then all I can think of is;

Your trying to take too much wood off at once,

Maybe your gouge or other tool isn't sharp enough and its digging instead of cutting,

Your belt may be stretched out and slipping on the pullys,

Re: Delta Lathe motor size

#4

Re: Delta Lathe motor size

Frederick Nelson

>The Delta 46-700 (or 701 with the stand) is a 12-inch by 34 inch lathe with Reaves (variable pulleys) drive. If this is what you have, it only has a 3/4 HP motor. It is actually a pretty good spindle lathe, as well as a good lathe for learning. The speed range of 500 to 2000 RPM is a little anemic on the low end (low torque once the belt begins to wear) and a little unreliable on the high end (the fixed portion of the drive pulley on the motor can be pushed PAST the retaining ring on the motor shaft by over-zealous pressure on the speed lever - this results in a speed range of about 0 to maybe 1000 RPM with NO torque anywhere along that band. The fix is to take the headstock housing off and reposition the pulley, which can then be pushed out of position easier the next time). The lathe works best with the speeds kept firmly in the middle of its range.

The stand that comes with the 701 version, and available separately, is stamped steel and a bit light. It can be modified with a ballast box mounted on the spreaders - 150 or more pounds of sand does wonders for the lathe's stability.

Except for the mentioned shortcomings, which I don't run into all that often, I do find the lathe quite adequate for my purposes - small to mid-sized spindles and similar-sized lidded boxes. I do wish it had more power, but I suspect replacing its worn belt could go a long way towards overcoming that complaint.

FNelson

Re: Delta Lathe motor size

#5

Re: Delta Lathe motor size

Pete in Holland, MI

>My Jet 1236 I initially thought was underpowered, but mostly I get slippage in the belt with the Reeves drive. Rarely see the motor really struggling. I put a new belt on the other day and that helped some (like last time), but I wonder if it is the right belt for the Reeves drive? The belt that came with the lathe is known as a "wrapped" belt, where the fabric making up the belt is wrapped up to make the belt. There are cut belts, where the pulley contacting surfaces are cut. The belt is built up kinda like a large tube, then sliced off like a rubber band. Snowmobiles & go carts that have a similar system of drive use this cut-belt technology, and I'm wondering if it would be better on our little lathes ?

Re: Delta Lathe motor size

#6

Re: Delta Lathe motor size

kkamm

>Thanks for everone's suggestions. I think you are probably right in that I won't see much benefit from changing the motor. For replacing the belt, did you get one from Delta ? Also on your ballast box, do you have any photos to share?

Thanks for the help.

Kieran

Re: Delta Lathe motor size

#7

Re: Delta Lathe motor size

Frederick Nelson

>This is about the best I have at the moment. It shows my tool rack (that normally hooks between the stand and the lathe bed) better than the ballast box. I'll see if I can get a better shot later today.

Beneath the lathe stand is a square frame that raises the lathe 3-1/2 inches, bringing the spindle height up to a more comfortable (for me) level. This is just four 4x4's bolted together, with a 3/8" recess on top for each foot, and a 3/8" pad beneath each foot to make up for the recess.

The box is simply half-inch plywood, with 1x2 reinforcements at the inside corners. The box is a truncated pyramid fitted into the space above the stretchers and beneath the top of the stand. The inside seams are sealed with silicone caulk to help contain the 185 pounds of loose sand inside. To get the sand inside, there are two loosely fitting lids on the top surface resting on their openings. I had originally intended to use t-shaped toggles wedged between each lid and the top of the stand, but I find gravity works just fine for keeping the lids closed. In the event I have to move the assemblage, (more like a "when" than an "if") there is a drain hole at one end, allowing the sand to drain into a bucket or two. The drain hole is reinforced with a second layer of plywood in that location only, and fitted with a gravity held plug (turned, of course,) to keep the sand inside. All this is probably much more elaborate than it really needs to be. I have Swedish engineers on one side of my family, and German engineers on the other - it shows up from time to time.

If I were doing it again, I would do something like Dominic Greco did with his Jet 1642, suspending a simple box between the spreaders, and using bagged sand instead of loose sand. See Dominic's article in "WC Articles & Reviews" for inspiration. Its complicated design notwithstanding, the setup is remarkably resistant to vibration, and if I stand on the base frame and use my considerable weight to try and tip it, it doesn't move. (Unfortunately, I can't move it easily, either - we just had a new washer and dryer moved in and, naturally, they had to go by the lathe.)

Drop me an email if you'd like to see some other pictures of the assemblage, and perhaps some details of its construction.

FNelson


img