Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

Square-Edge Bowl Mishap

Posts

Square-Edge Bowl Mishap

#1

Square-Edge Bowl Mishap

Barry Turner

>I tried my first square-edge bowl today. The blank was a 5" x5" x 2" piece of Honduras Mahogany. All went well as I mounted the blank on the woodworm screw of my Super Nova chuck and proceeded to turn the back side of the bowl. I was sanding with a small piece of sandpaper, when my hand slipped and a couple of the wings cut two small, but deep gashes in my second finger. Ouch!

After a little self-applied first-aid, I resumed turning and finished my first square-edge bowl, a little wounded and perhaps, (hopefully) a bit smarter. Watch those wings!

Re: Square-Edge Bowl Mishap

#2

Re: Square-Edge Bowl Mishap

John Lucas

>Barry I used to sand under power on winged bowls but I quit. I use a drill with a 2" disc and turn the lathe off. I found that it was too easy to vary the thickness of the edge with the power on. I've also bruised my fingers sanding by hand with the lathe on.

Re: Square-Edge Bowl Mishap

#3

Re: Square-Edge Bowl Mishap

n2wood

>So when do we get to see a picture of this thing?

Re: Square-Edge Bowl Mishap

#4

Re: Not the fingers, but..

JamieDonaldson

>.....the bowl please! John is right about sanding with the lathe off, as you can now testify, but we've all learned such lessons the hard way!

Re: Square-Edge Bowl Mishap

#5

My First Rule on Shop Injuries

Barbara Gill, Remlik VA

>DON'T BLEED ON THE WOOD! :-)

Re: Square-Edge Bowl Mishap

#6

Re: My First Rule on Shop Injuries

Barry Turner

>The wood is safe, but I did drip a couple drops of blood on my lathe.

Re: Square-Edge Bowl Mishap

#7

Re: Square-Edge Bowl Mishap

Barry Turner

>Well, I've got to take one first..........then figure out how to post it on this board. :-)

Re: Square-Edge Bowl Mishap

#8

Re: Square-Edge Bowl Mishap

NotsoDull!

>It seems to me, any object lesson learned without major bloodshed or broken bones is a huge success.

Re: Square-Edge Bowl Mishap

#9

Re: My First Rule on Shop Injuries

NotsoDull!

>Either that or switch to blood wood!

;-)

Re: Square-Edge Bowl Mishap

#10

Re: Square-Edge Bowl Mishap

Dick Anderson

>Barry:

I have made a number of winged edge and square edged bowls. I try to make the wing about 1/8-inch or less thin. The process I use is to begin with the bowl on a screw chuck and form the bottom of the bowl and wing to completion. I will leave a small tenon to chuck the bowl to turn the inside and upper face of the wing. For the bottom of the wing I use a bowl gouge taking the wing down in stages (steps) from outside to inside of wing. As each step comes to the final level that I want to achieve then it is smoothed using a skew chisel as a negative rake scraper. When the bottom of the wing reaches its final point of meeting the bowl the lathe is turned off and the wing hand sanded usually starting with 400 grit and proceeding to what ever final grit want. The bowl is then reversed for hollowing and completing the wing to its final thickness following the same step procedure used on the bottom, that is, working from the outside toward the inside of the wing. As each step or stage is completed it is smooted with the negative rake scraper and blended with the previous section.

I hope this is understandable, but it always keeps my hands and fingers out of the way. I will also mark with masking tape on tool rest the extreme outside point of the wing.

Re: Square-Edge Bowl Mishap

#11

Job Ain't over.....

Barry Irby

>until bleed has been declared.

Re: Square-Edge Bowl Mishap

#12

safe way

JKJ

>I saw a safe way to do square turning in an old article. Glue scrap wood to the sides and turn a disk instead of a weapon. Safe to turn, safe to sand. Then cut off the scrap sides on the table saw or band saw and finish the edges.

JKJ

Re: Square-Edge Bowl Mishap

#13

Sounds Much Safer.

Barry Turner

>

Re: Square-Edge Bowl Mishap

#14

Re: THAT'S CHEATING!

JamieDonaldson

>Its much more entertaining to turn it square, and the edges are visable, which allows more precise and uniform control of thickness.

Re: Square-Edge Bowl Mishap

#15

Re: This may help

RussFairfield

>I wrote an article about turning a square bowl for the AAW Journal a long time ago. This is an exerpt of the safety part of that article. There is a photo of the bowl from the article at the end. I apologize for the photo.

Turning the wings involves an interrupted cut that becomes nearly invisible at their tips � the �ghost�.

SAFETY RULES --- Again!

Safety Rules are published and promoted by the AAW to make the lathe a safer place for all turning activities. All of these rules are especially important when turning a large �square�. From personal experience, the following four are critical:

1.

Be alert at all times. Know what you are doing and where you are going with every movement. Know where the �ghost�, tool, hands, arms, face, and body are, and their relative locations at all times.

2.

Always rotate the work by hand BEFORE running the lathe, and NEVER move the tool rest while the lathe is running. No further explanations are needed.

3.

Always wear a full face shield. It is far better to hit the mask than your nose when we forget Rule #1. Also, sharp splinters can be broken away from the wood at the corners.

4.

Relocate the START/STOP switch so that it can be reached without passing either hand or arm near the �ghost�. The switch on most lathes is not in a safe location. If you don�t want to move it, or install a remote STOP, you have been warned!! I have had two encounters with the �ghost�, the first while reaching for the OFF button, the second the ON button. Then I moved the switch.

The Lighting

Visibility is as important as a sharp tool and safe working habits for turning on the �ghost�. A 100-watt clear incandescent bulb with a reflector is ideal. More light than that and the background becomes illuminated through the �ghost�. Many turners have advocated placing sighting boards behind and opposite the turning to enhance the �ghost�. I have found them to be a poor substitute for a bright light shining on the working area. The sighting board only provides a uniform background, while the bright light accents the surface of the �ghost�. Both might be necessary in a brightly lit shop (I don�t have that problem).


img

Re: Square-Edge Bowl Mishap

#16

Re: THAT'S CHEATING!

Barry Turner

>I agree..........but having a bleeding finger is not much fun either!

Re: Square-Edge Bowl Mishap

#17

Re: THAT'S CHEATING!

Doug Trembath

>Hence the lesson, Barry.

I tell students and those at demos that I bled all over the lathe until I learned a few remarkably simple propositions.

1. You can't see the outside edges of an intermittent surface at lathe speeds.

2. You never cut or sand past the 12 o'clock position on the inside of a bowl, and more especially, box.

ad infinitum, (or nauseum, as you prefer).

Adding wood to the exterior has been popularized by Vic Wood for years, and is an essential part of his class discussion. He was a bit miffed at me when I told him I thought it was a waste of time and effort.

FWIW, I find you can easily prepare for the winged or intermittent cut by hand rotating the piece until you find the portion closest to the tool rest, place your gouge in the proper position, turn on the lathe, and find the surface with the back of the gouge. Then you know where to aim for, and you can follow the shape.

$.02

Doug Trembath

Studio in the Woods

Re: Square-Edge Bowl Mishap

#18

Re: Another use for a laser pointer

RussFairfield

>Make a mount for a laser pointer so that it can be located above the lathe and aimed downwards. Then position it do that it just hits the tips of the wood. You will always be able to see where they are.