Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Help! thinning wipe-on poly--Russ, or?

Posts

Help! thinning wipe-on poly--Russ, or?

#1

Help! thinning wipe-on poly--Russ, or?

Ken Grunke from SW WI

>My can of Minwax wipe-on poly is starting to get a tiny bit syrupy. It's still quite fluid, but dries faster than it did a week ago because I left the cap off a couple times. I'm having trouble with wipe marks, because of it.

Need to get a couple pieces ready for delivery on Saturday to the Contemporary American Woodturner exhibit at the Rochester Arts Center in Minnesota, deadline is Tuesday!

I'm trying to decide if I should make the special trip into town just for a new can (1/2 hr drive) or can I thin it with mineral spirits? I'll get a new can on Saturday, but my submissions have to be on the road by then unless I can do one-day shipping on Monday.

Yikes!!

Re: Help! thinning wipe-on poly--Russ, or?

#2

Stealth gloat?

Carole in VA

>Can't help with the finish problem but congrats on the exhibit. :)

Re: Help! thinning wipe-on poly--Russ, or?

#3

Re: Help! thinning wipe-on poly--Russ, or?

Bill Stehman

>Ken,

Yes you can thin poly, I always buy the large cans and transfer it into 6 oz plastic squeeze bottles from Wally World. I thin most 10 to 20 % and find this helpful in filling in open grain woods, using steel wool back to the wood between coats. It takes more coats but dries faster. I then use full strength for the last two coats.

Re: Help! thinning wipe-on poly--Russ, or?

#4

Re: Help! thinning wipe-on poly--Russ, or?

Mark Mandell - Gone Round In Jersey

>Ken,

You can thin it (or re-thin it), but the thickening indicates the start of polymerization. While MS will do, since you're going to be getting new stuff anyway, you can also use v&mp naptha. Even though naptha dries more quickly (higher vapor pressure), it allows the poly to flow and level much better than MS so it's better at emliminating lap and stroke marks. Drawbacks are that you get a thinner film, it will be more likely to sag on vertical surfaces, and the unused thinned mix will start to gel in about a week even in a tightly sealed can. When I hand-apply poly, I mix it in small batches and then just ditch the unused portion.

Hope this helps

M

Re: Help! thinning wipe-on poly--Russ, or?

#5

Re: Stealth gloat?

Ken Grunke from SW WI

>LOL! Carole, congrats are a bit premature, as this is a juried show--I don't even know if I'll be accepted, and I've got some good competition!

Thanks anyway :)))

Re: Help! thinning wipe-on poly--Russ, or?

#6

Re: Help! thinning wipe-on poly--Russ, or?

Ken Grunke from SW WI

>Mark, what you said about polymerization confirmed my suspicions. If I find some naptha, otherwise I'll make the trip into town. This is too important for me to mess up, but now I know that I can still use the stuff for less critical work.

Thanks, your reply was very helpful!

Re: Help! thinning wipe-on poly--Russ, or?

#7

typo: I'll try naptha if found

Ken Grunke from SW WI

>

Re: Help! thinning wipe-on poly--Russ, or?

#9

Re: Help! thinning wipe-on poly--Russ, or?

RussFairfield

>The only problem with an aging oil finish is that it will take longer to cure, and when it has gone far enough it will stay softer than a fresh oil.

If you can tolerate a softer finish that takes longer to dry, ir is OK to use.

Re: Help! thinning wipe-on poly--Russ, or?

#10

Re: Help! thinning wipe-on poly--Russ, or?

Ken Grunke from SW WI

>Drying doesn't seem to be a problem with this gloss polyurethane, Russ--it dries too quickly.

I wonder if I can use it in a spray gun, and get good results instead of trying to wipe it on. Guess I can only try. Half a can left, only 6 months old--I should just buy smaller cans, might save a buck or two in the long run!