Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

If you sell to woodworkers, your customers are already here

Homemade Grinder Idea

Posts

Homemade Grinder Idea

#1

Homemade Grinder Idea

Todd O. Cronkhite Maine Native now in Jax Fl.

>Yesterday I had a brainstorm and thought that I'd take and old 1/3 h.p. 1725 r.p.m. motor, turning it upright in a box, mount a grinding stone to the shaft, make a tool rest above it and use it to grind some of my lathe knives. Think this would work?

It's along the lines of a horizontal wet grinder only dry.

I currently use a handcranker with a homemade Wolverine to grind the knives, but I really don;t like the "hollowing effect" it leaves on the skews and gouge bevels. I think flat would be better.

Todd O.

Re: Homemade Grinder Idea

#2

Re: Homemade Grinder Idea

don lewonczyk

>Hi, I'm in no way an expert on grinding wheels but from a safety stand point I've read that is a dangerous practice to use the side of a grinding wheel turning that fast. It's not made for side grinding and can easily disentergrate sending fragements at the 1750rpm's into your face and body, like getting shot. Slow speed grinders are only turning at 90rpm's or so and you can use the sides to grind. Like everything else people ask for input and then they decide what they are going to do. Hope this helps, DonL

Re: Homemade Grinder Idea

#3

Re: Homemade Grinder Idea

Raymond Overman in SC

>Make sure the grinding wheel you buy is made for use on the side. Standard stones you buy for a grinder are not meant for use on the sides and can have catastrophic failure. You'll probably want a a pulley system that will greatly decrease the speed from 1700 RPM also for a home made Tormek type grinder.

Re: Homemade Grinder Idea

#4

Re: Homemade Grinder Idea

John Lucas

>Todd My first turning grinder was done by using a spare motor and putting the grinding wheel directly on the shaft but I mounted the motor so the wheel turned in the usual way to use the outer surface of the wheel. As the others have said I would not grind on the side of a wheel that isn't designed for that purpose.

Re: Homemade Grinder Idea

#5

Re: Homemade Grinder Idea

Ernie Miller

>If you don't like the hallow grind how about getting out one of the stones that you use for plane blades? if you need a real fine cutting one I have a nice Black one you can buy. ;)

Re: Homemade Grinder Idea

#6

Re: Homemade Grinder Idea

Barry Irby

>In addition to the questions about running the wheel horizontally and It's not being designed for that, I suspect the motor is not made to run in that position either. Someone may know better, but the bearing may have been designed for supporting the shaft horizontally, but not vertically.

Re: Homemade Grinder Idea

#7

Re: Homemade Grinder Idea

Ken Grunke from SW WI

>Now that you've probably been talked out of this idea, I'd like to add some encouragement for it. I've been thinking of doing the same thing myself even though I have a standard grinder. I would use the face of a standard grinding wheel myself, since the ones used for face grinding are not cheap. But like others have said, I'd slow the speed down instead of using direct drive. I don't see much problem having a motor vertical if it's kept lubricated, that's the main concern. Drill press motors are vertical. A ball bearing motor would work fine without that concern.

I'd use an old thick aluminum saucepan as a shell around the wheel, with a drain at the bottom and a hose connected to that, coming from a small pump circulating water. Probably a 4 to 1 pulley drive to step it down to around 450 rpm--at that speed, the wheel flying apart is really not a concern, especially with a heavy aluminum pot guarding it. And that pot is the frame of the unit, tap and drill it for mounting tool rests. G'ahead, I say!