Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Hosaluk handles

Posts

Hosaluk handles

#1

Hosaluk handles

Carole in VA

>Does anyone happen to know if the Bosch adapters will fit the Hosaluk handles? I am going to order some stuff from CS and if those adapters will fit the Hosaluk, it will save me some shipping to throw them into my order.

Re: Hosaluk handles

#2

Re: Hosaluk handles

Mark Kauder, Phenix City, AL

>Carol,

If you have the ability, can you measure the diameter of the openings?

If you do, I will go out and measure the Bosch adapters I have.

Or if I get off my butt in a few minutes, I will send you the outside dimentions of the ones I have.

Mark

Re: Hosaluk handles

#3

Re: Hosaluk handles

Carole in VA

>Mark,

The holes in mine are 1/2" and 5/8". The screw holes are .87" apart (measured center to center)

Re: Hosaluk handles

#4

Re: Hosaluk handles

Mark Kauder, Phenix City, AL

>It is a no-go.

The holes are 1" apart center to center.

With the Bosch adapters, as you neck down to a smaller gouge, you have to put one adapter inside the next larger. The largest adapter is 21/32".

Mark

Re: Hosaluk handles

#5

Re: Hosaluk handles

Carole in VA

>Well crumb! Thanks, Mark.

Re: Hosaluk handles

#6

Motor bushings?

Gerry in Maryland

>Carol,

I have the Kelton handle and when I need to go down from the 5/8� to a half inch I use a standard motor shaft bushing from the hardware store. They are about an inch or so long and have a slot the whole length that the Kelton�s screws can go through to hit the smaller shaft.

Hope this helps!

Gerry

Re: Hosaluk handles

#7

Re: Hosaluk handles

Michael Stadulis, in Gloucester County, NJ

>Hi Carole. I think that the Bosch handles are aluminum while the Hosaluks are steel..... so there is a weight difference if that is a consideration. I like my Hosaluk handle alot.

Mike

Re: Hosaluk handles

#8

Re: Motor bushings?

Carole in VA

>Thanks Gerry. I need to go from 1/2 to 3/8. Will check out the bushings.

Re: Hosaluk handles

#9

Re: Hosaluk handles

Carole in VA

>Michael, they do come in steel but mine is aluminum. Still fairly hefty though!

Re: Hosaluk handles

#10

Re: Motor bushings?

Jorge Castaneda

>Carole,

Packard offers a 3/8" handle adapter, $10.95, it is made for the Shure Grip tool handles, but I got it and use it in my Kelton with no problems.

mis dos centavos

Jorge

Re: Hosaluk handles

#11

Oneway

Jorge Castaneda

>Carole,

I failed to mention that the Shure Grip Handles are made by Oneway

Re: Hosaluk handles

#12

Re: Hosaluk handles

Edward

>Mike Hosaluk is marketing a newly designed handle. Well actually it is the same as all the other handles on the market, but new for Mike. The new ones have an aluminum core with anodized al. ends. 12 and 18 inch lengths. He also has an 18 in. one out of steel, for the additional weight. I have some of his early ones that were all steel and found them a little too heavy. These new ones are a nice weight, for me. I have only seen them in the Packard catalog, so far.

Re: Hosaluk handles

#13

Re: Why buy bushings??

RussFairfield

>You can make a perfectly good adapter from a piece of Hard Maple, and drill the holes for the screws where you want them.

If the OD and ID are a good fit, these things will last for years, and the price is right.

Re: Hosaluk handles

#14

Re: Why buy bushings??

Mark Kauder, Phenix City, AL

>You beat me to it, Russ. My Vega has a 1.25" tool post, I bought a Oneway curved tool rest. It has a 1" tool post. So, I turned a bushing out of Cocobolo - works like a charm.

Thought about Carol's predicament this morning, and when I saw the tool rest.....

Mark

Re: Hosaluk handles

#15

Re: Hosaluk handles

Jack Brown, Western PA

>Carol

I have several of the Hosaluk handles and know that he makes a bushing/adapter that goes from 5/8 to 3/8 I don't use a bushing I just put a 3/8 tool in the 1/2" hole and tighten the screws. It works for me

Re: Hosaluk handles

#16

Re: Why buy bushings??

Carole in VA

>Now why didn't I think of that??? Just happens that I have a piece of hard maple that was given to me day before yesterday. Thanks Russ.