Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Jet Mini - VS Conversion

Posts

Jet Mini - VS Conversion

#1

Jet Mini - VS Conversion

Gary Ratajczak

>Hello to all.

Looked at the price of the conversion kit to make my Jet Mini into a VS model - over $200.00 with shipping!!!

Anyone had success with a source and procedure for anything other than the kit conversion on the mini? I found some old info on the web using some surplus motors, but nothing is available anymore.

Just wanted to see if anyone else has been messing around before I try to re-invent the wheel.

Thanks

Re: Jet Mini - VS Conversion

#2

Re: Jet Mini - VS Conversion

Bob Lemon - Sacramento CA

>Gary,

Try the drive system of treadmills. Now is a good time to start picking them up at the thrift stores.

Re: Jet Mini - VS Conversion

#3

Treadmill motors *LINK*

Fred in NC

>I am with Bob Lemon on this one!

Treadmill motors are usually permanent magnet 90 VDC, rated at 1 HP or more. A used but working treadmill can supply most of the parts, although the controller will look a bit unusual for a lathe . . .

When I did my conversion, I ordered a new motor pulley from Jet Tools, so I could leave the original pulley and motor intact. I had to bore out the pulley to fit the DC motor. Also, I mounted the DC motor under the lathe, in a cabinet I built for it. This required longer belts, which were ordered from Aarubco Rubber Co. (cheapest and best service, no affiliation).

A an alternative, Surplus Center sells DC motors and controllers at reasonable prices. Their best controller is the Minarik, at about $60, and you would be wise to add heat sinking to the aluminum frame. As for motors, their 130 VDC motors can run on 90 volts, losing about 1/3 of the HP. That will leave about 1 HP which is more than plenty for the mini lathes.

Replace the AT for my email address.


Lathe cabinet

Re: Jet Mini - VS Conversion

#4

DC Motor Controller

Clem Wixted

>Fred,

When you installed your controller on the Vega motor did you rework the controller so you don't have to turn the speed to "0" before you turn it up, whenever you stop it.

I picked up one of the Vega motors and controller some time back, on the recommendation of Mark Kauder. I also have picked up a working treadmill and have taken the motor off. The controller is different from the one that came with the Vega and I woulder how I can modify it so it will be right for lathe work. Or, should I get another controller that schematics are available for modification.

Clem

Clem

Re: Jet Mini - VS Conversion

#5

Re: DC Motor Controller

Fred in NC

>Clem:

1. I have seen the mod instructions for the VEGA controller. I decided to leave it alone. The motor starts at the lowest speed and then ramps up in speed until it gets to the selected speed. The motor has a tachometer which sends feedback to the controller. The result is that for a small workpiece it gets to speed very fast. For a heavier or out-of-round piece it takes longer.

I think this is a very desirable feature. Check the threads on the old Nova controller, which was would start very fast.

2. The treadmills I have seen have some sort of digital control with pushbuttons. In my opinion they would be a pain in the neck for use with a lathe. Check the plate on the motor to determine the voltage. Most likely it will be either 90 or 130 VDC. Surplus Center has controllers for either voltage. The use a potentiometer for speed control, which I like. Remember that you can run a 130 VDC motor on 90 V, with about 1/3 loss of power. This is ok since treadmill motors are at least 1-1/2 HP. I would add heat sinking to the controller in any case, since heat is what destroys the output transistors.

Re: Jet Mini - VS Conversion

#6

And for reversing..

Clem Wixted

>...did you just pur a DPDT center off switch in line with the motor?

Are you now officially retired?

Clem