Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Sharpening upgrade

Posts

Sharpening upgrade

#1

Sharpening upgrade

John Veerkamp

>I know this subject has been around the block many times but I'm looking for specific experience with the Delta 8" slowspeed grinder, model 23-725. If any of you have experience with this grinder I'd like to hear your opinions. I have some Christmas gift money that is earmarked to upgrade my sharpening system. I have the Wolverine jigs but I am using it for now on a Grizz 6" 3450 rpm grinder. All opinions appreciated.

Thanks,

JohnV

Re: Sharpening upgrade

#2

Re: Sharpening upgrade

Michael Stadulis, in Gloucester County, NJ

>Hello. I like mine. No Oneway balancers and it's almost as smooth as my Baldor 6".

-Mike

Re: Sharpening upgrade

#3

Solid machine...

Peter Teubel

>That is one solid HEAVY grinder. You can't go wrong with that one.

Re: Sharpening upgrade

#4

Re: Sharpening upgrade

Barry Turner

>I have the Delta Slo-Speed 8" grinder. I have had it for about 4 years and have found it to be very satisfactory. I am using it with the Oneway Wolverine system. If the grinder has a fault it's the 100# weight. But, that's one of it's greatest assets, too. I don't even have the damn thing bolted down. It hasn't moved in 4 years. Just grab a friend to help you move it into your shop. I finally replaced the 60 grit gray wheel with a 60 grit pink from Woodcraft. I'm still using the original equipment 120 grit white wheel. I considered replacing the white wheel too, but found it works much better if dressed often. Be sure to buy a diamond grit wheel dresser. It's money well-spent.

Re: Sharpening upgrade

#5

Re: Sharpening upgrade

Russell L. Babbitt Jr.

>Excellent. Switched from a Tormek. I have been using it for about 2 years with ceramic Norton wheels 80 grit from Craft Supply and the Wolverine. Many other club members have the same setup except for the wheels and many pros when they come to demo will ask for the Wolverine on an 8" grinder.

Re: Sharpening upgrade

#6

Ditto:

T Daniel

>I have used the 8" Delta 1800 rpm for about 3 years now. I did use Tormek but I found I could buy the Delta for the price of a new stone for the Tormek. The Tormek did a good job on gouges but had to be dressed to go to a flat tool. I found myself using the 8" Delta more and more and the Tormek less and less until I finally just retired the Tormek. The 8" Delta is supposed to be obsoleted and replaced by the junk 8" variable speed model. Get one while there are some left.

TD

Re: Sharpening upgrade

#7

Re: Sharpening upgrade

John Veerkamp

>Thanks for the replies. Ordered mine this morning.

John

Re: Sharpening upgrade

#8

Another Ditto

David Propst

>I love my Tormek, but I also have the Delta and it is a very fine machine. If it is being discontinued, get one quick. I got mine from Packard about three or four years ago. Amazon shows one in stock.

Also I very much recommend the Oneway Balancing system.

Happy New Year!

Davd

Re: Sharpening upgrade

#9

Re: Another Ditto

Jim Shaver - Oakville, Ontario

>Hi David,

Yes, I love the Oneway Balancing system. I installed one on my grinder and was so impressed I bought one as a gift for a close turning friend who also loves it too!

Take care,

Jim

Re: Sharpening upgrade

#10

Something I Noticed this Morning

Garrett in Victoria

>I had to kill half an hour at a Borg this morning, so wandered to the tools section. They had 4 grinders on display (all 6") and set on an eye level shelf. Bored, I spun the wheels on the no-name, and saw a tiny bit of run-out. Hmm. Spun the Delta, a little more. Spun the house brand and still more. Finally, gave the Dewalt a spin and was truly astounded. The wheels were so crooked they left a shdow line about 1/4" wide. All spun smoothly and seemed balanced, so it must have been the wheels themselves.

But it bothers me that the "name" brand - also the most expensive, of course - clearly does no quality assurance on the third party wheels it puts on its grinders.

Cheers, Garrett

Re: Sharpening upgrade

#11

It is not the wheels.....

T Daniel

>it is the thin metal plates that hold the wheels. Many of the manufacturers have quit using machined plates and are now using plates that resemble stamped washers. The One-way balancing kit recognized this problem and designed their kit to include new plates that hold the wheel 90 degrees to the shaft. Another common problem is that people will try to correct a wobbling wheel by dressing the sides of the wheels; this is a no-no. When you dress the sides of a wheel you must take exactly the same amount off on both sides of the wheel or you will throw the balance off just that much more. It is better to spend a few more bucks on a good grinder than to keep pouring money down a well trying to make a cheap grinder work. I would rather have a belt sander than a cheap grinder.

TD

Re: Sharpening upgrade

#12

Re: It is not the wheels.....

Chas

>In the UK at least one Replacement Wheel supplier supplies Replacement Machined Flanges to replace the "pressed steel" efforts used on the cheaper grinding machines, worth an enquiry from your local Wheel Specialists. This is often enough to fix the problem without further balancing.

Re: Sharpening upgrade

#13

Re: It is not the wheels.....

Vicmarc.fan

>I have the "junk" new VS grinder with Oneway balancing kit. It runs so smooth I can balance a nickel on it at any speed. I had a problem with the kit because of clearance around the wheel covers. Had to mount the wheels with the bolt heads inside. Just pay attention to which way yuou tighten the kit so they don't loosen over time.

Ron