Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

200+ woodworking book reviews

Deer antler pens (please respond if you know,)

Posts

Deer antler pens (please respond if you know,)

#1

Deer antler pens (please respond if you know,)

Blake Washburn (12 year old turner)

>I'm still wondering how to turn deer antler. I would like to know how to cut it, drill it, and chuck it for a pen. If you know how to do any of these things, please respond as soon as possible. :)

Blake

12 year old turner

Re: Deer antler pens (please respond if you know,)

#2

Re: Deer antler pens (please respond if you know,)

Jeff Taylor - Bloomington, Indiana

>Greetings Twelve-year-old-turner!

I make antler pens and penlights all-of-the-time.

Drill like anything else, slowly, and shallow.

Turn like plastic, by taking light cuts.

Be careful when sanding, the open poreso the marrow will pickup the sanding dust and discolor. Flooding with thin CA will help ...

Finish like plastic ...

Here is a pic of a set I sold just before Christmas.


--jeff


img

Re: Deer antler pens (please respond if you know,)

#3

Re: Deer antler pens (please respond if you know,)

John Lucas

>Blake I've only made one so take this with a grain of salt. The piece I had was crooked, thin and my friend wanted a pen so I stupidly said I could do it. The pieces were more rectangular shaped,crooked and just barely thick enough to make a pen. After considerable thought I cut it into pieces that were a little longer than the brass tube. Then I mounted each one between center guessing at the best location for the centers.

I put light pressure on the drive and then started cutting the antler using extremely light pressure. This showed me exactly how the cut was progressing and whether or not I had chosen the right center. I readjusted the center until I had the antler spinning with the thickest areas in the middle. Then I took the long point of my skew and cut each end as square as I could leaving a small tenon. I cut the tenons off on the belt sander.

This gave me a piece that was flat on both ends and relatively round. They were then easy to clamp in my vise and drill in my drill press using a 7mm drill. If I did it again I would probably turn the antler down between centers until one end was completely round and then chuck it in my 4 jaw chuck and drill it on the lathe. This would be more accurate I think. Of course if you want to leave the antler more naturaly shaped the first method would work.

Re: Deer antler pens (please respond if you know,)

#4

Re: Deer antler pens (please respond if you know,)

Ron in Drums PA

>I've never turned antler, but. . .

www.penturners.org

has folks that can lead you in the right direction

Re: Deer antler pens (please respond if you know,)

#5

Re: Deer antler pens (please respond if you know,)

Sam Scalzo

>I have turned many Deer Antler pens. Be sure and wear a mask. You are turning bone and it can be toxic. The hard part is getting the hole drilled straight. The thiner the antler the better color.

Re: Deer antler pens (please respond if you know,)

#6

Re: Deer antler pens (please respond if you know,)

Bruce Kantelis

>Hello!

Antler turns like most other materials. Stinks like crazy, be prepared for the smell. You need a piece that you can drill, that can be difficuly, often you need to place it at some odd angle to get a hole in a useable place. The color and texture of the pen will vary depending on how thick the antler piece is. You almost always remove most/all of the exterior surface.

For me the greater challenge was finishing. Sand to very fine like you would plastic. I finish with CA glue and have the best success with that on antler.

Regards,

Bruce

Re: Deer antler pens (please respond if you know,)

#7

Antler pens

ChuckS

>Blake, most of this is a repeat of what's already posted, but here goes.

1. Lay the pen tubes you will be using along side the antler & mark where to cut the antler.

2. Cut a little (3/8ish) long

3. Mount between centers on lathe & adjust so you can later drill without breaking out of the side & still have enough wall thickness. I do this by turning the lathe on & holding the pen tube near the rotating blank. Adjust as needed.

4. Rough the blank- still between centers. This is give you a true surface on the sides of the blank so you can drill. True up the ends if you want, but leave long. (I don't bother)

5. Drill. I drill by chucking the blanks in my lathe & mounting a drill in the tailstock. I also drill wet-- less dust & cooler running. Heat is BAD for antler. If I use my drill press, the antler tends to grab the drill & force the drill into the blank.

6. Trim to size with pen mill. Again, I do this wet.

7. Turn like plastic. Sharp tools, light cuts. If you cut into the softer layers, flood them with CA & continue.

8. Sand carefully, heat is BAD. I sand wet to 1500, then use plastic polish.

9. Finish, or not. I like to leave antler unfinished if I have not gone into the softer layers. It will polish beautifully, and over time will develop a patina from the user's hands. Fill any soft areas with CA glue, sand, & polish. If it's mostly soft, just finish with CA.

Work slow, try not to produce dust, & don't breath it. Antler dust is BAD.

All the hassle is worth it, the pens will be beautifull!

Have fun!

ChuckS

Re: Deer antler pens (please respond if you know,)

#8

Drill mod

Phil Joines

>For plastic and antler if you grind a small flat on the inside of the drill flute so that it's 90 deg to the cutting edge it won't grab nearly as much. You're making a scraper out if it.

Re: Deer antler pens (please respond if you know,)

#9

Re: Drill mod

jared

>remove for email

Hello A couple of more questions along this line as I need to make some antler pens too.

I have the drill bits that I bought from Berea hardwoods that they specifically recommend for drilling pen blanks. they have a special word to describe them but I forget what it is now. Anyway are they good for drilling antler?

When you turn the piece of antler between centers, what centers do you use on the head stock and tail stock to do this?

thanks in advance Jared

Re: Deer antler pens (please respond if you know,)

#10

Re: Drill mod

Phil Joines

>If the drill is a "brad point" I wouldn't use for antler or plastic. They will dull it in short order and are tough to sharpen. They work great for wood. What you want is a normal twist drill in 9/32", should be available from a good hardware or tool store.

For centers, a live tail center with a point and, if you have one, a miniature spur center. Ideally, the spur center needs a short, narrow point so you can relocate the antler to get it to run true. If the point is too large the hole it makes won't let you move it.

Re: Deer antler pens (please respond if you know,)

#11

Drill mods & Centers

ChuckS

>Cool, I'll grind a couple bits as described & keep them exclusively for antler.

The Berea bits seem to work great. They are parabolic flute twist drills, not brad points. They are also available at industrial tool supply houses, but the price isn't any better. They do catch antler...

I prefer a "safe center" at the headstock end. It has a short point inside a cup center-- no spurs. It will allow a catch without the following detonation and allows easy repositioning. They are expensive from Oneway, but something like 8 bucks at Sears.

Lots of good info flowing around here that is not @ penturners or other sites!!