Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

what is "the line of fire"?

Posts

what is "the line of fire"?

#1

what is "the line of fire"?

Tom Sontag - St. Louis

>All this talk of standing out of the way of spinning bowls and things has me asking the painfully obvious. Having not yet launched one, am I correct that the line is perpendicular to the spindle/spinning axis and near the headstock? In other words, don't stand facing a spinning bowl in line with the bowl facing the lathe? Is that the only "line" to worry about? I also sense from the article section that leaning in to get wapped by a bouncing tool is a bad idea...

Re: what is "the line of fire"?

#2

Re: what is "the line of fire"?

Bill Howatt

>That is the line of fire alright but depending on the size of the object, the speed and other physical phenomena like a big catch it can vary. Smaller objects can bounce off of walls and get you. Don't restrict the line of fire to just the front of the lathe, things can go out the backside too. I remember in grade 8 woodshop class getting a catch with my skew and having it fly out of my hands towards the back of the lathe into the lumber storage area. If somebody had been standing there watching me they would have been skewed! For that reason I never watch demos from that position.

Bill

Bill

Re: what is "the line of fire"?

#3

more..." in the line of risk"

e

>the challenge is in estimating the risk.

there is more risk directly in front of the work as it is powering up. therefore, i tend to stand to the side as the rpm increases.

also, there is more risk in roughing out -- bark will fly off and fractures exposed as i start taking wood off. or if the wood is spaulted, i tend to work from the side also.

however, sometimes you need to stand directly in front of the spinning work, for example, taking that last clean cut.

it all a matter of reducing the risk ... although sometimes 'poop' happens!

Re: what is "the line of fire"?

#4

Re: more..." in the line of risk"

e

>... also, when i'm demo-ing with the lathe between the audience and me, i keep the area directly in front of the lathe cleared of viewers ... just another risk-reduction method.

Re: what is "the line of fire"?

#5

Re: what is "the line of fire"? *LINK*

Raymond Overman in SC

>A loose piece spinning rapidly toward the tool rest could go pretty much any direction once it hits the rest including straight up. There have been tales of things hitting the ceiling and coming back down on someone's head.

The most unfortunate example of this that I have read was on Bill Grumbine's website. A link is provided below. I hope you don't mind Bill.


Unfortunate Incident

Re: what is "the line of fire"?

#6

Re: what is "the line of fire"?

Barry Irby

>Tom, One night I prepped a blank about 7 inches in diameter and 14 inches long. It had about seven sides and had been hacked out with a chainsaw. I mounted it between centers and was going to turn it to a cylinder, just to see what it looked like before quitting. Instead of reaching for my face shield with my right hand and stepping aside, I turned the lathe on with my left had. That block came off there like lightening and hit me dead center of the forehead, just above the eyebrows. My glasses flew away and were lost. I called a neighbor for help (I was home alone) and went to the emergency room and received 28 stitches. Right to the bone. Kid you know there are three layers? I got stitches in all three. Bled like a fountain.

So now that you know what the line of fire is, stay out of it. Imagine your bowl blank or whatever becoming a very large weed eater or flail like a chain mace.

Check your mounting procedure very carefully, turn slow, don't turn cracked blanks, wear the gear.

Re: what is "the line of fire"?

#7

Simple

Mark Mandell - Gone Round In Jersey

>It is the particular spot which lays along a sometimes straight, but often tortuous path where you do not want to be standing when some object on the lathe in your immediate vacinity manages to slip those "surly bonds" and go whither it will.

It's less a "line of fire," and more of a "kill zone."

M

Re: what is "the line of fire"?

#8

Re: what is "the line of fire"?

JKJ in East TN

>The physics say any piece coming off will tend to fly straight out in a plane through the piece and perpendicular to the axis, but as mentioned by others, once a piece hits something else it can change direction. I remember one back in the '60s that went off the wall and then sideways across the room and out a high window (which was somewhat noisy since it was closed at the time).

I am careful to stand to the side when spinning up a piece for the first time, when roughing anything that is the least bit out of balance, or when turning anything heavy. And remember low speeds mean less kinetic energy in the piece.

I think the best defense is to ALWAYS wear a face shield. One author mentioned that after a painful bouncing incident he prefers to wear a hard hat with an attached face shield. You can get these at any industrial safety supply house.

JKJ

Re: what is "the line of fire"?

#9

Re: what is "the line of fire"?

jeff jilg

>I count this as the 5th incident on the woodturning forums reported this year where a faceshield would have reduced injury or avoided it altogether. (2 on AAW, 2 here on WC, and 1 on WOW). The other incident earlier this year where Duane got conked out, would not have benefitted from a faceshield.

My faceshield is always on before the powerbutton gets touched. One thing that is nice about the Trend Airshield and other PAPR's is that they provide more forehead protection.

Re: what is "the line of fire"?

#10

Re: what is "the line of fire"?

George Fitzpatrick - Springfield MA

>I ALWAYS put my faceshield on and stand to the side before hitting the power switch.

That being said, how do you stand to the side while roughing out a blank, especially one out of balance? I do have a tendency to turn at the slowest speed on my midi when roughing out (500 rpm)but on the bigger chunks I can fit on the midi, it can still bounce around some, and I find I need to stand in the line of fire to maintain my own balance.

Once the piece is turned to a cylinder, and after re-checking to make sure it is secure, I will then gradually increase speed.

After the holidays, it's a Trend for me, though.

Looked at the above link, and still find it hard to believe that the guy was actually propelled into the rafters!

geofitz13

maker of fine sawdust

Re: what is "the line of fire"?

#11

Tom, the "line of fire" is.....

TD

>90 degrees to the centerline of the lathe bed and radially in any direction. If the loose piece hits the toolrest or the safety guard or a wall behind the lathe, etc it will change direction though. When roughing the outside of a bowl the safest way is to mount the piece with #12 screws, good ones, not the junk from the local box store, slow the lathe down, and stand facing the bottom of the bowl (tailstock end). Use a push cut moving the gouge from right to left, handle down (really down), flute turned to about 10 o'clock, toolrest at 45 degrees to the lathe bed. This should keep you out of the "line of fire". Beware of guards, glasses, hoods etc that give you a false sense of security. A 20 pound chuck of wood spinning at high rpm will go through most plastic hoods like they were't even there; also, the give no protection for the forehead. Guards stop a piece that was going away from you and return it into your face. Get in the habit of always turning your lathe to minimum speed before leaving it (Wally's suggestion, and a good one).

TD

Re: what is "the line of fire"?

#12

I think that is what happened to me last week

Mike Schwing from Md.

>I've been trying to figure out how a fist sized chunk of a bowl came flying up towards my eye socket so as to knock my safety glasses right off my head.

I was standing outboard, facing the interior of the spinning bowl blank. The bowl appears to have fractured along a spalting line, and I have to believe that it got loose on what was to be its final cut/pass, traveled down, bounced off the toolrest/banjo/interior of bowl and back up into the interior, rattled around and wound up ejecting itself straight up towards my face. I have no idea how else this could have happened.

My eye is fine today, still a little bruised looking, but my sight has returned to normal. (whew!). I'm alternating between kicking myself for not wearing my face shield and not, because in that situation safety glasses alone are commonly accepted as safe. At least they WERE, not any more. I believe the face shield would have made this incident nothing more than a bummer.

Re: what is "the line of fire"?

#13

Re: I use "free fire zone" as ....

JamieDonaldson

>.....we defined it in Vietnam- the area where anything that moves is a potential target.

Re: what is "the line of fire"?

#14

Re: what is "the line of fire"?

JKJ in East TN

>>That being said, how do you stand

>to the side while roughing out a

>blank, especially one out of balance?

I usually stand just to the left and reach to the right for roughing a unbalanced one. However, I've been roughing with a spear pointed scraper lately, the best method I've found for an extremely rough blank. This requires almost no finesse, no bevel rubbing, and no careful control so I think it's easier to rough from the side than with a gouge. I've been meaning to post a picture if I can find the time to take it.

JKJ

Re: what is "the line of fire"?

#15

Psssst, George . .

Mark Mandell - Gone Round In Jersey

>Don't tell anyone, okay? But it was a goof set up between Bill, Tommy and a neighbor who was a real fireman to celebrate Bill's then-new Poolewood lathe. Just remember though, you didn't hear it here. Great picture set was originally on Badger Pond.

|;-}}}

Re: what is "the line of fire"?

#16

Don't Fret George

Raymond Overman in SC

>The first ten times I went back and looked at the pictures (and chuckled once I got to the part where the guy was all right) I thought they were real too.

Re: what is "the line of fire"?

#17

Re: what is "the line of fire"?

George Fitzpatrick - Springfield MA

>Okay, so you got the new guy.... ;) (he said sheepishly)

The feet dangling from the ceiling was a great touch. I figured with my midi, it could only launch me through sheetrock, anyway!

geofitz13

maker of fine sawdust

Re: what is "the line of fire"?

#18

Re: Psssst, George . .

JKJ in East TN

>...it was a goof set up...

Keep in mind that a person hit with a block thrown with enough energy to lift him off the ground even a little bit would certainly not be in any condition to climb down a ladder later, if ever.

JKJ