Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Veritas - Innovation in Tools

Sanding Vases - Is this for real?

Posts

Sanding Vases - Is this for real?

#1

Sanding Vases - Is this for real?

Buddy Booker

>I've tried a lot of techniques but sanding the inside of vessels by putting something inside (Silicon Oxide, Sand?) and letting the lathe run for a while at first glance seems to be a stretch. I do remember tumbling turquoise years ago but the inside of hollow forms?

I picked this up in a couple of old threads. Anyone know of anyone using this method or did I just get sniped?

Re: Sanding Vases - Is this for real?

#2

Re: Sanding Vases - Is this for real?

Allen Neighbors

>It's for real. Look below, until you find the subject "Sanding inside Hollowforms and Vases", Andrew Bourke, 16 December 2005. I didn't believe it at first, but I'm just an old guy who'll give it a try.

I've used dowels with leather taped on the end, and sandpaper taped to that, and about anything else would be better than my experiences. Some sharp gravel would probably work. Regards, AL

Re: Sanding Vases - Is this for real?

#3

Re: Sanding Vases - Is this for real?

TD

>It works if your lathe will run slow enough. The lathe has to run very slowly so the rocks will slide and tumble. At a couple hundred rpm the rocks will just be pinned against the side of the vessel and will not slide and tumble. I use granite gravel but I plan to try some lava shortly. It takes about 12 to 24 hours of tumbling to give any significant results. I use the biggest stones that I can fit into the opening plus a few smaller ones tossed in for good measure and I fill the cavity about half full. Works for me!

TD

Re: Sanding Vases - Is this for real?

#4

Re: Sanding Vases - Is this for real?

Barbara Gill, Remlik VA

>TD...so you leave your lathe running for 12-24 hours?

Re: Sanding Vases - Is this for real?

#5

yep.

TD

>

Re: Sanding Vases - Is this for real?

#6

A Word Of Caution

Barry Turner

>I think I would be reluctant to leave my lathe runninng this slowly for as much as 12 to 24 hours. I would be afraid the controller would overheat. You might want to check with the manufacturer to make sure this is safe.

Re: Sanding Vases - Is this for real?

#7

Re: Make a bowl spinner

RussFairfield

>Make a bowl spinner. And, it can be used for finishing.

All it takes is a 3/4" shaft that is threaded on one end, 2 cheap pillow block bearings, a couple pulleys and something like a BBQ rotisserie motor for a drive, and an adapter for the threaded end of the shaft to fit your chucks or faceplates. It looks kinda like a cheap home-made lathe headstock.

It can have fixed pulleys. 60 RPM is about right for things in the 6-12" diameter range. Or it can be fancy with a small fractional HP mechanical variable drive. The variable speed works better because the rotation can be adjusted to what works best for the size abrasive being used. You might need more HP than than the turkey spinner for laege forms and heavy rocks.

It makes gloss finishes easier because heavy coats of gloss poly and lacquer won't run if the work is rotating slowly. The variable speed is better for finishes because the speed can be selected to just fast enough to stop the run, but not so fast as to move the finish outward to a larger diameter.

This description is only intended to give someone an idea to tinker with, and make their sanding and finishing a little easier. It is not a how-to article, so there will be no pictures or drawings.

Re: Sanding Vases - Is this for real?

#8

Re: A Word Of Caution

Bill Howatt

>The motor itself may overheat since the internal fan would be turning slowly. Motors designed for VFD use are supposed to have higher temperature ratings to account for this but excessive heat is usually best avoided. If you have a step pulley system then problem could be reduced by running on the lowest speed pulley to keep motor rpm higer; fan blowing on motor would help.

One would hope that a Oneway was designed with this sort of activity in mind but perhaps not the cheaper makes.

Bill

Re: Sanding Vases - Is this for real?

#9

Re: Sanding Vases - Is this for real?

eliot

>You don't have to do all this.

Check out Bruce Hoover on the internet. He sells an attachment for the Milwaukee close quarter drill called Extend A Sand. It's basically a tube with a rod down the center. The tube fits over the drill, and the rod goes in the drill chuck. At the other end of the rod is a keyless chuck to hold sanding mandrels. In other words, it's essentially a very long (about 13 inches) chuck that's stiffened by the tube.

Hoover is a superb turner who invented the sanding glove and various turner "friends" like this Extend A Sand. One can reach him at

The Sanding Glove

1752 Big Rd

Bloxom, VA 23308

phone 757 665 4597

fax 757 665 1999

(I don't have any connection with him other than attending one of his demos at my turning club and buying some stuff from him.I'm looking at one of his invoices now.)

You can also buy a long hemostat which you use to grab some sandpaper that's folded over a sponge , or whatever, and hold it against the inside of your vessel while you sand. Just be careful to hold the hemostat AROUND the finger holes --NEVER put your fingers THROUGH the holes!