Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

ADVERTISE HERE - FREE TRIAL

Extreme hollowing as promised

Posts

Extreme hollowing as promised

#1

Extreme hollowing as promised

TD

>George Van asked about hollowing in a thread further down and I promised to post a picture. This is a shot of something that cannot be done with a Jamieson or a Kelton and I do not know if it can even be done over a bed; for this one I move to the VB as it becomes much easier. The flat top with wings makes this a very difficult piece (don't try it at home) because the invisible wings with saw teeth like to chew on knuckles. The armbrace unit with curved tip (by Don Pencil) makes it possible though not easy. As I said in the thread below, every tool has limits.


img

Re: Extreme hollowing as promised

#2

Re: Extreme hollowing as promised

George Van in WI

>And......A picture is worth a thousand words. Thanks Terry, for helping me make better e tools I have and the ones I need to get.

Re: Extreme hollowing as promised

#3

Keith Tompkins

Re: Extreme hollowing as promised

Keith Tompkins

>Hey TD, It can be done on a long bed lathe.....I just stand on the wrong side of the lathe....works very well. I usually don't post about that, because it may be misinterpreted by some. I wouldn't want to see someone try it and get hurt in the process.

Also., lathes with outboard capabilities work as well... NIce piece!

Re: Extreme hollowing as promised

#4

Re: Extreme hollowing as promised

Mike Schwing from Md.

>Terry, unless I'm missing something, that position/setup is easily possible with the Kelton system captured system.

Nice, difficult piece you got going there!

Re: Extreme hollowing as promised

#5

Don't think so....

TD

>Mike, I don't think the Kelton can make the sharp turn unless the top were domed more; the flat top is what makes it difficult along with the natural edge which prevents the sharp turn because the natural edge hits the handle. Just another reason to buy more tools.:)

Re: Extreme hollowing as promised

#6

Re: Extreme hollowing as promised

Mac

>For someone who said three years ago" I don't do hollow forms cause they take too long and I cant make any money on them,and I dont color anything,I like the natural look",seems to me that you are getting mighty close to THE EDGE there fella....he he.....

Re: Extreme hollowing as promised

#7

Re: Extreme hollowing as promised

Anthony Y

>Lock down the chuck, switch the tool around and run the lathe in reverse. The Pencil tool makes it easier as it is machined on both sides.

Re: Extreme hollowing as promised

#8

Re: Don't think so....

Phil Joines

>I have made a cutter bar set with a swivel joint. There are two ends, 4" and 6" long for it. It was a PITA to make without a milling machine. I think they could do it. It would take a fair amount of adjusting of the tips so the hand held would probably be faster. Of course it takes a lot more skill :>).

Re: Extreme hollowing as promised

#9

Re: Don't think so....

Mark Kauder. Phenix City, AL

>Wally has a captured system that has an articulated head on it, it can get just about anywhere, from any angle.

Mark

Re: Extreme hollowing as promised

#10

Re: Don't think so....

Mike Schwing from Md.

>Ok but I still think I can do exactly what you've pictured with the Kelton hollowing rig.

Re: Extreme hollowing as promised

#11

Re: Don't think so....

joaz

>my kelton takes me were ever i want to go...from the deep stuff to hollowing goblets...you cant beat it.

Re: Extreme hollowing as promised

#12

Works very well

Wally Dickerman in Arizona

>It was made by John Nichols. Very secure in a deep vessel. It can be very aggressive however.

Wally

Re: Extreme hollowing as promised

#13

Challenge!

TD

>Give er a try Mike. With all the hollowing tools I have I have no plans to make another one of these, even though I have it sold at a very good price. If I make another similar one I will make some changes: The wings will have to turn outward which will get them out of the way of the tool handle or the "lid" will have to be shallower or not as flat. I would love to hear your comments aftere making one.

TD

Re: Extreme hollowing as promised

#14

WC ers made me do it!

TD

>See what happens when you let other WCers in your shop? Mac comes down with a bunch of far-fetched ideas and then Russ comes along and puts some dye in my best oil finishes and now I am all messed up. Now all I need is for Molly to come by with that smoky thingy!

TD

Re: Extreme hollowing as promised

#15

Re: WC ers made me do it!

Carole in VA

>Don't let Mike in there or you'll be doing carved, dyed, burned, hollow bugs. ;)

Re: Extreme hollowing as promised

#16

Re: Challenge!

Mike Schwing from Md.

>I'll have to relay that challenge to the guy I sold my hollowing rig to, but he posts here so he'll probably see it anyway. I'm still convinced I can do just what you've shown with that rig, but will have to find someone else to prove it.

Re: Extreme hollowing as promised

#17

Re: WC ers made me do it!

Mac

>Terry, You gotta start standing up for yourself,oops,I'm sorry,you are standing up....

Re: Extreme hollowing as promised

#18

Now Mac...

TD

>That is like the pot calling the kettle "black"?

Re: Extreme hollowing as promised

#19

Re: Now Mac...

Pete Kekel - Kentucky

>Mac? Making short jokes? Wow . . .

Re: Extreme hollowing as promised

#20

Re: Extreme hollowing as promised

Ben Aragon

>George,

Great looking vessel.

Ben