Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Combination Press Plough Plane

cracking bowl

Posts

cracking bowl

#1

cracking bowl

Patrick Capobianco

>Is there anything I could do to fix a cracking bowl? This is my second bowl I'm turning and it is maple I started turning the outside yesterday and when I returned to turn the inside I noticed it stared to crack. So still went ahead and turned the inside I figured I needed the practice anyway but would like to salvage it if I could.

Re: cracking bowl

#2

Afraid to answer

TD

>Pat, I don't know whether we should answer this or not. Many times cracks can be taken care of in various ways but if we try to answer you without seeing the crack we might cause you an injury. Small cracks are frequently taken care of with thin CA adhesive, larger cracks need a sawdust/epoxy mix. The main thing is the integrity of the bowl while you finish turning it. If there is mold in the crack the above things will not adher. If you decide to proceed, take light cuts so that you do not rip the piece apart. If the wood isn't valuable I would toss it and start over. When you leave the lathe for more than half an hour you should slip a plastic bag over the turning so that it will not crack.

TD

Re: cracking bowl

#3

Re: cracking bowl

Patrick Capobianco

>here is a picture.


img

Re: cracking bowl

#4

Re: cracking bowl

Don Evans

>Pat:

TD is 100 percent correct but I'll add that when I have to leave a turning as TD described I would take paper towels and wet them, wrap them around outside and inside of turnin and then cover with zip bag.

Due to neck and upper back problems I have to do that alot because of being unable to finish in one session when doing large stuff, 8" dia or more.

Don

Re: cracking bowl

#5

Toss it!

TD

>

Re: cracking bowl

#6

Re: Afraid to answer

Joe Herrmann

>It looks to me that the blank cracked while it was waiting for you to finish the turning. Terry is correct in that the best course of action is not to let the cracks develop in the first place. Whenever I have to leave the lathe, even for a short length of time, I always cover the blank with a plastic shopping bag and wrap the wings around the blank to seal it as best I can. I have had bowls begin to crack in as little as 5 minutes.

I haven't had much luck in filling the cracks--at least none that I have been happy with.

Joe

Re: cracking bowl

#7

Re: cracking bowl

John Lucas

>Don I put a plastic bag over the piece. I sometimes go days between sessions depending on my work schedule. This has always worked for me.

Re: cracking bowl

#8

Steven Antonucci

Does the crack go all the way through?

steve antonucci

>It looks pretty deep, but if you could turn the outside down (carefully, lathe running very slowly to minimize the "shrapnel" effect), you might be able to turn the cracks out. Then follow normal preventative care.

If I know I'm risking a crack, I bury the form in the newly cut shavings (right at my feet)- definitely helps, and is very easy to do.

Steve

Re: cracking bowl

#9

Re: Does the crack go all the way through?

adrien

>If you've got some extra tightbond or white glue, mix it 50% with water, soak the cracked side and see if the crack closes.....If so you might take another crack at it. Remember to have the thickness even all the way from top to bottom.

Re: cracking bowl

#10

Re: Does the crack go all the way through?

adrien

>If you've got some extra tightbond or white glue, mix it 50% with water, soak the cracked side and see if the crack closes.....If so you might take another crack at it. Remember to have the thickness even all the way from top to bottom.

Re: cracking bowl

#11

Re: cracking bowl

Carole in VA

>Patrick, if there is any question at all, toss it. There is plenty of wood out there but only one you. BTW, if you do the plastic bag trick on green wood, try to keep the chuck and jaws out of the bag or you may get rust. I just fold the wings of the bag up tight against the wood and shove my toolrest up against it to hold it. If it's really wet wood, I remove the whole works - chuck, wood and bag - from the lathe if it is going to sit for any length of time so the inside of my spindle doesn't collect moisture and rust.

Re: cracking bowl

#12

Re: cracking bowl

Earl Eyre

>Adrien mentioned, almost in passing, to remember to keep the thickness even throughout the bowl. If you are turning green wood, I want to underline that. The single biggest factor in cracking is letting the bowl dry with varying thickness. That causes different stressing on the bowl and cracking will happen. Also, I always wrap the bowl in a plastic bag when I leave a green piece unfinished. I will also spray the bowl with water if I'm having a tough time during turning and it is starting to dry unevenly while I'm turning.

The key is keeping the piece evenly dry or moist--while turning and drying. The pros can turn a piece very fast and eliminate the problem. I'm slow so have to do everything possible to keep the moisture even while I'm turning.

Earl

Re: cracking bowl

#13

Re: cracking bowl

Allen Neighbors

>I want to begin this post with "I am a beginning turner!". Been turning only a little over a year. But here's what I do: If the crack is 1/32" or wider, I crush turquoise into fine powder, and mix with epoxy; force the epoxy/turquoise into the crack with a pallette knife, cover the filled crack with scotch tape and let dry. If it's smaller than 1/32" I do nothing until it gets bigger.

I would appreciate some help in this sort of thing, also.

AL