Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Exotic Hardwood, Personally Sourced Worldwide. Inspected at Origin. Shop Rare Stock.

Would chucks work for inside-out turning

Posts

Would chucks work for inside-out turning

#1

Would chucks work for inside-out turning

Bill Howatt

>Hi,

I am thinking of trying an inside-out turning. I know the recommended method is to glue up the pieces using paper and then split apart for final assembly and turning. I do recall seeing a clip of somebody doing one and he had a special shopmade chuck that fit his pieces.

I have a Oneway Stronghold and Talon which are supposed to hold square stock. I also have a Oneway Live Center and an adapter for the Talon to screw onto the center.

Can I assemble my 4 blanks and mount in the Stronghold and the other end in the Talon? Will this hold them tightly so the final assembly will have a good joint?

Thanks,

Bill

Re: Would chucks work for inside-out turning

#2

Re: Would chucks work for inside-out turning

John Lucas

>Bill The chuck works great for one end but you then have to deal with the other end. A reverse cone on the tailstock will work but this assumes you have extra wood as well as the wood that goes into the chuck. If you have 2 chucks and a Oneway tailscenter you can buy the adaptor that lets you put a chuck onthe live center. This would be really good for inside out turning except you couldn't do thin pieces. The centrifigal force of starting the outboard chuck spinning would probably rip the inside out turning apart.

There are lots of ways to hold inside out turnings. you can put CA glue on the wood about 1/2" from each end. The you can either break this joint of cut it off after 1st turning. You can put screws in the ends. You can use hose clamps but be careful, they really hurt when you hit them with your fingers. I put masking tape over them to help protect my hands.

For experiments on small pieces I use nylon straping tape to secure the pieces. Wrap it so that it won't come unwound when it is spinning toward you. It happens really really fast.

I use a paper joint because it is much more secure. If you start with a solid piece of wood you don't even have to have a joint. You simply bandsaw it into 4th's after the initial turning.

Re: Would chucks work for inside-out turning

#3

Re: Would chucks work for inside-out turning

Bill Howatt

>Thanks, John, for the great tips. I do have the adapter to mount the chuck on the live centre (I use it to center bowls for vacuum chucking) but I hadn't thought about the torque forces destroying thin turnings.

Bill

Re: Would chucks work for inside-out turning

#4

Re: Would chucks work for inside-out turning

John Lucas

>Bill If you have a variable speed lathe just turn the speed down each time you shut it off and that won't happen unless it's a very thing turning. I have a Nova Live center that has a #2 morse taper to hold the centers. I thought I would turn a really long thin spindle with the tail end as a #2 morse taper to sort of stretch the spindle. It worked great until the spindle got thin. I turned it on and the spindle twisted itself in half trying to turn the live center. This weights a lot less that a chuck so I think a chuck would add considerable force to a turning when it starts to spin.

Re: Would chucks work for inside-out turning

#5

Thanks, Have VS, just have to remember!

Bill Howatt

>

Re: Would chucks work for inside-out turning

#6

Re: Would chucks work for inside-out turning

Jorge Castaneda

>I saw a demo where the presenter used a chuck and in the tail end, the four sticks where jammed inside a short lenght PVC pipe, so the cone would not split them apart, it works great, and offers no danger to knuckles.

Jorge

Re: Would chucks work for inside-out turning

#7

Re: Would chucks work for inside-out turning

Roger Smith

>Bill, I use a 1/2 inch piece of duct tape on each end for the initial turning. Chuck one end and use the reverse cone on the tailstock. Hey, it holds fenders on at 200MPH.

Re: Would chucks work for inside-out turning

#8

PVC or metal rings: a little math

Ken Grunke from SW WI

>If you have a given size of ring, multiply it by .35 to get the size of the individual squares where 4 of them will fit inside the ring.

They may not fit tight enough, so subtract say, 1/16" from the ring I.D. so you can nip a little off the outside corners and wedge the ring on tight.

Besides a PVC ring cut from drainpipe, I use bearing races, big washers, a short piece of metal tubing, jar lids, any ring-type dohickey I can find kicking around.

Re: Would chucks work for inside-out turning

#9

Re: Would chucks work for inside-out turning

Craig Daymon

>Just got back from a turners meeting tonight which featured inside-out turning. I should know his name, but I'm not good at names. He is well known for his inside out turnings.

He used a Talon chuck on one end, taped the 4 pieces together with masking tape at the other end and used a cup center. (I'm drawing big blanks tonight, but I think that is the right term. Point in the middle of a circle?) He chipped off the corners of the tailstock end so the point of the center wouldn't drive them apart. That's the way he likes to do it and I wish I could think of his name cause it would help cement this as a good way to do it.

He turned a lightning bolt tonight, which involves reversing the direction of every other piece after turning inside out. He also had examples of turning card symbols, Heart, Diamond, Spade, Clubs as well as a female nude silouette and a Christmas ornament with a heart.

-Craig