Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Sioux/Milwaukee angle drill $39

Posts

Sioux/Milwaukee angle drill $39

#1

Sioux/Milwaukee angle drill $39

Dave Thompson - Champaign IL

>Sioux and Milwaukee sell a close quater 55 degree angle drill for megabucks. I just found one in an unlikely place with no-name. Don't know if it's another venue from the same manufacturer, or just an independent knock off.... regardless, I ordered one and received it today. It works well, and still looks identical as far as I can tell.

enjoy,

Dave

PS. Not affiliated in anyway with the vendor other than having been a one time customer.

Re: Sioux/Milwaukee angle drill $39

#2

Re: Sioux/Milwaukee angle drill $39

Mark Mandell - Gone Round In Jersey

>Sounds like you got yourself a $100 Rolex, Dave.

Good luck with it. Just remember not to leave it plugged in when not being used. |;-}}

M

Re: Sioux/Milwaukee angle drill $39

#3

Re: Sioux/Milwaukee angle drill $39

GaryG in MD

>Dave,

In absolute terms, you got a good deal, and I'm sure you'll get lots of good use out of it. That's what counts. However, FWIW, for others who might be interested, per page 12 of the December issue of More Woodturning, you can get them for $29.90 from JMTools. I just ordered one myself.

Regards,

Gary

Re: Sioux/Milwaukee angle drill $39

#4

Re: Sioux/Milwaukee angle drill $39

Basil Biberdorf

>Haven't looked at close quarters drills at all, much less Sioux/Milwaukee ones. However, Big Lots here in south Texas has a Shop Source-labeled one for $25. FWIW.

Re: Sioux/Milwaukee angle drill $39

#5

Re: Sioux/Milwaukee angle drill $39

Bob/Great white North

>Just my two cents worth, I'm really disappointed with the Sioux.

Had it for just over a year,< off warranty of coarse > and the

rear armature bearing seized-up and took out the plastic housing.

There were very few hours on it and was cleaned reguarly.

Anyway I've bought a $60 air angle die grinder and works much

better and hasn't missed a beat.

O ya, up here the Sioux goes for over $250, good day EH!

Re: Sioux/Milwaukee angle drill $39

#6

Re: Sioux/Milwaukee angle drill $39

Norm Smith in Nova Scotia

>You can buy the knockoff right angle drills on EBay.

Re: Sioux/Milwaukee angle drill $39

#7

I have the real thing

TD

>I sell the Milwaukee close quarter drill for $100 including shipping. These are new but are tagged as "re-manufactured". They are actually overstock and were bought just before Milwaukee sold to AEG. I don't know if I can still get them or not. With any of these drills it is important to stop using them immediately if you hear any bearing noise. The bearing is supported in plastic and if it gets hot it will melt the plastic that supports the bearing. When the rear bearing goes out replace it with a sealed bearing, not the standard shielded bearing. The sealed bearing costs about $10. When you take the drill apart to replace the bearing take a photo before you disturb anything inside as the trigger mechanism is a bit confusing when going back together.

TD

Re: Sioux/Milwaukee angle drill $39

#8

Re: Sioux/Milwaukee angle drill $39

Mark Kauder, Phenix City, AL

>You can get rebuilt, real Milwaukee Close Quarters Drill all the time on Ebay for about $69. OR you can get knock offs for $39.

I have one of each. I have had the bearings replace in the Milwaukee once after about 2 years use. I used the knockoff while it was in the shop. The Milwaukee is much better, I use the heck out of it. The knockoff is acceptable, though it sounds a little rougher, and the speed control at the trigger is not as smooth.

If my Milwaukee ever dies, I will replace it with another, but I will keep the knockoff around for an emergency spare.

Mark

Re: Sioux/Milwaukee angle drill $39

#9

Re: Sioux/Milwaukee angle drill $39

Barry Turner

>It may look identical, but I doubt that it is internally. It may have bushings instead of bearings. Still, for $39 versus $189, it's probably a good value. When it breaks down, throw it away. You may find it will last longer than you might expect.

Re: Sioux/Milwaukee angle drill $39

#10

Damn Fine Watch!

Barry Turner

>A $100 Rolex knock-off is a damn fine watch for someone who is accustomed to $29 Timexes.

Re: Sioux/Milwaukee angle drill $39

#11

Panasonic 9.6 volt Cordless

Barry Turner

>What is it with close quarter drills. I have been using my old Panasonic cordless drill for power sanding bowls for quite some time now. I have not seen te need for a close-quarter drill. In fact, my cordless may be easier to control because of the T-handle grip. Top RPM is 1500, which is plenty fast for power sanding. Any faster and you run the risk of heat-checking.

Re: Sioux/Milwaukee angle drill $39

#12

Re: Panasonic 9.6 volt Cordless

John Lucas

>I agree Barry. I've been using my $64 dewalt for at least 4 years. And I mean heavily both sanding and drilling all kind of things. I decided that I had gone through 4 of the $29 black and decker models so I upgraded a little when I got the Dewalt(even though they are made by the same people). This thing really takes a beating.

Re: Sioux/Milwaukee angle drill $39

#13

Re: I have the real thing

JR in south Louisiana

>TD

Do you know where the sealed bearings can be purchaced?

My drill starts to whine every month or so. I usually open it up an

shoot it with silicon spray.

thanks

Re: Sioux/Milwaukee angle drill $39

#14

Re: Damn Fine Watch!

Barry Irby

>I have a $10 Bolex. It's 13 o'clock all day every day.

Re: Sioux/Milwaukee angle drill $39

#15

$29, $25.... Doh! Oh man!.... ;-)

Dave Thompson - Champaign IL

>

Re: Sioux/Milwaukee angle drill $39

#16

Re: Panasonic 9.6 volt Cordless

Barry Turner

>My Panasonic is 10+ years old and is still going strong. Panasonic makes a very good line of cordless drills. Everyone thinks Panasonic only makes TV's, CD players, DVD players and stuff, but they are real contenders in the realm of cordless power tools. They really have it together on battery technology. When this one croaks, my next cordless drill will be a Panasonic. I'm so used to it, I think I would have problems switching to a close-quarter drill.