Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Identify and use hundreds of woods

Broke a Bowl Gouge Today...

Posts

Broke a Bowl Gouge Today...

#1

Broke a Bowl Gouge Today...

Ryan Dicker in Renfrew, Ontario

>Well my Henry Taylor 3/8" bowl gouge is 2" shorter that it was yesterday.

I was coring out a fairly solid piece of dried box elder (I had picked up the blank at a wood show) when I felt a sneeze coming on. So I pulled the gouge off the tool rest, sneezed, then looked back to the bowl and put the gouge down to the rim where there was still some hard sealer on it. I hadn't meant to touch the gouge to the wood yet but dumb me sneezed with my face shield on and couldn't see anything...It cought and broke.

I wanted to get this bowl done tonight but now I'm a little depressed. What's even worse is that I have a foot switch controlling power to my lathe which I could have easily let off of...

Oh well, I guess worse things have happened.

Thanks for reading my sob story. I guess the moral of the story is that you should always lift your face shield if you have to sneeze...

Ryan

Re: Broke a Bowl Gouge Today...

#2

Re: Broke a Bowl Gouge Today...

Russell L. Babbitt Jr.

>Don't be too depressed it sounds like you still have ten fingers and other desired appendages........

Re: Broke a Bowl Gouge Today...

#3

Re: Broke a Bowl Gouge Today...

Ed Karch in No.VA

>I always have it down when I am trying to blow the dust off something. I only spit once with the chainsaw face guard down.

Re: Broke a Bowl Gouge Today...

#4

Re: Broke a Bowl Gouge Today...

Bill Neddow

>Been there, Ryan. Done that. I think it is part of the learning curve. Mine wasn't a bowl gouge, though. It was a spindle roughing gouge.

I hope it was not one of the new gouges you bought last weekend.

Re: Broke a Bowl Gouge Today...

#5

Re: Broke a Bowl Gouge Today...

JKJ in East TN

>You might contact either the company or the store where you bought the gouge and explain. They may replace it for free. It's happened before.

JKJ

Re: Broke a Bowl Gouge Today...

#6

Re: Broke a Bowl Gouge Today...

Ryan Dicker in Renfrew, Ontario

>Unfortunatly I bought it a year ago from Lee Valley, so a replacement is unlikely. I certainly learned from the experience and plan to mount the broken piece and put it up on the wall as a reminder. :D

Ryan

Re: Broke a Bowl Gouge Today...

#7

Re: Broke a Bowl Gouge Today... *LINK*

JKJ in East TN

>>Unfortunatly I bought it a year ago from Lee

>Valley, so a replacement is unlikely.

It still might be worth a try. A gouge shouldn't snap like that. I'd send both the store and the manufacturer a picture of the two pieces. You stand to lose nothing and perhaps gain a new gouge.

See the note in the link. Also, read this thread:

http://www.woodcentral.com/cgi-bin/archives_turning.pl?read=75185

JKJ


Broken Gouge Replaced

Re: Broke a Bowl Gouge Today...

#8

Re: Broke a Bowl Gouge Today...

Bill Howatt

>Ryan,

I certainly don't believe in trying to make anybody come good for something that was my fault. However, was your catch extremely severe or did you snag the bowl when the gouge was well off the rest such that it slammed down hard.

Can't say that I've ever had the problem but I have read a number of posts in the past where the brittle cast-iron tool rest was fractured not the tool when it was slammed down. (I am sure I will now hear of hundreds of cases the other way around :) )

As you know, the people at LV are very pleasant and helpful. Why not give them a call and tell them what happened and ask if it may be a fault in the tool?

Good luck,

Bill

Re: Broke a Bowl Gouge Today...

#9

Re: Broke a Bowl Gouge Today...

Bill Crommett

>I have two shortened roughing gouges due to my own negligence. But I just ground a new and thicker tang on them and mounted them in stouter handles. With two short roughing gouges I will never miss the extra inches in my lifetime, but I am reminded to move the tool rest up closer once in a while.