Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

Sharpening skews?

Posts

Sharpening skews?

#1

Sharpening skews?

Jim K in Trappe PA

>Hi all,

How do you sharpen your skews - flat or hollow ground?

Ernie Conover says in his book to (gently) use the side of the grinding wheel to keep the bevel flat.

I inherited a wolverine jig, but it will hollow grid the bevel.

Also, do you hone after grinding? If so, with what?

Thanks,

Jim

Re: Sharpening skews?

#2

Re: Sharpening skews?

JKJ in East TN

>Jim,

I hollow grind with a Tormek then hone many times with a small paddle-type diamond hone (very fine) before regrinding. The hollow grind makes it very easy to hone perfectly as you simply press the hone tight to both the edge and the heel of the grind with the forefinger. This makes it impossible to mess up the honing. Just imagining, but I suspect it would be difficult to properly hone a flat grind and even then, honing several times might significantly change the dynamics of the cut. Regardless, be careful with grinding on the side of a standard wheel since I understand they are not designed to do this safely.

The Tormek has a 10 inch wheel when new which makes a fairly shallow hollow grind. I haven't tried a hollow grind with a 6" or even an 8" wheel so I don't know how the deeper hollow would affect my control of the skew. (My Tormek wheel is down to 9.5" or so after a few years of use.)

JKJ

Re: Sharpening skews?

#3

Re: Sharpening skews?

Jorge Castaneda

>Jim,

One person I know that knows skews is Alan Lacer, I saw him in a recent demo, he free hands it on the grinding wheel, makes it hollow and slightly round and after sharpening hones it with a 600 grit diamond stone, the hollow helps, that way the hone is touching only in two points, the edge and the heel of the bevel.

The local High School shop teacher, sharpens the skews with oil stones, and puts a wonderful edge that lasts and lasts, his bevels are perfectly flat and straight and leave a perfect finish that needs no sanding.

Both persons say: "If you can see your edge, you have no edge"

mis dos centavos

Jorge

Re: Sharpening skews?

#4

Re: Sharpening skews?

Ken Grunke from SW WI

>I hollow grind on what started out to be an 8" wheel, but is now approaching 6". Doesn't seem to cause any trouble with a hollower grind, but when it gets down to 6" I'll replace it.

I made a large flat toolrest for my grinder, for good control and tto get a nice clean bevel without facets.

Between grindings, I hone with a flat diamond stick, then polish the edge on the flat face of an 8" MDF disk (or is it MDO?) which is chucked up in a little tabletop drill press. I use the white polishing stick for that. The polished edge leaves a beautiful surface on the wood, which if you've practiced your skew technique can be sanded starting with 320 or 400 grit.

Re: Sharpening skews?

#5

Re: Sharpening skews?

Bill Howatt

>I use a homemade jig like the Oneway. It leaves a hollow ground surface. I use a diamond hone to finish the grind and to touch up several times before going back to the grinder.

Bill

Re: Sharpening skews?

#6

JL

Re: Sharpening skews?

JL

>I started sharpening my skews on my Tormek. I find it easier to use waterstones though. As I usually keep them (the stones) in a covered kitty litter bucket they are usually ready for use. I don't know if I'd like using an 8". I wouldn't like using a 6".

Re: Sharpening skews?

#7

Re: Sharpening skews?

tek-Brunswick, Ohio

>Hollow ground with a slight radius on the edge. I use a Lee Valley Radius Skew Jig on a One-Way platform. I hone with a MDF wheel loaded with green compound. Occasionally I still use a diamond hone to touch up. As long as you have a reasonable bevel angle, a bevel that isn't conxex, and a sharp edge you should have a usable skew. The rest is user preference and practice, practice, practice. The Alan Lacer Skew video is worth watching. Richard Raffan and Mike Darlow are also proficient with the skew and worth reading or watching.

Tom

Re: Sharpening skews?

#8

Thanks all!

Jim K in Trappe PA

>

Re: Sharpening skews?

#9

Flat rest...

Peter Teubel

>...on the Wolverine jig w/8" wheel. I then hone/strop on a powered felt wheel. Razor sharp and a joy to use.

Re: Sharpening skews?

#10

Re: Sharpening skews?

Colin Spencer

>Why waste steel on a grinder? All I do with mine is touch it up with a diamond file everytime I use it. It is razor sharp and with a completely flat surface on the skew I find it far easier to control. Still it must be what works for you as has been said before there are no right oe wrong ways just what works for you.

Re: Sharpening skews?

#11

Re: Sharpening skews?

Ed in Leaside

>I must be in the minority then. Mine is flat ground on a 1x42" sander with the belt running up (vs down). I cut a wooden block at 12 or 13 degrees, drew some guide lines on the face like this \\\\//// at 20 degrees (IIRC), and clamped it to the rest. I find it not to be as "catchy" as the hollow ground bevel.

Ed

Re: Sharpening skews?

#12

Re: Sharpening skews?

John Lucas

>I've ground my skew both hollow ground and flat grind and don't find any difference in handling at all. The only difference is the ease of sharpening, at least for me. I hollow grind with an 8" grinder and then use diamond hones from medium to ultra fine the first time. Most of the time after that I just hit it with the ultra fine and maybe the leather stop. Eventually I notice it won't shave hair off my arm so I'll either step down to the medium hone or go back to the grinder depending on how long it's been since I've been to the grinder.

I tried using oil stones but the stones would get dished and start rounding my edge. I don't mind a round skew but eventually this makes it harder for me to sharpen back on the grinder.

Re: Sharpening skews?

#13

Re: Sharpening skews?

Barry Turner

>If you use the Oneway skew attachment, the bevels will be relatively flat. If you just use the tilting table, the bevel is hollow ground. After trying my skews both ways, I think I prefer the hollow grind better. I normally don't hone except to restore an edge without going back to the grinder. I use a fine credit-card diamond hone.