We value your privacy.
We use cookies to enhance your browsing experience, analyse site traffic, and personalise content.
By clicking “Accept all”, you consent to our use of cookies. You can also choose
“Essential only” or learn more.
>I wanted some relacement bits for my Stinger hollowing tools, which are 1" x 3/16" round HSS drill blanks. When I went to order them, shipping on one little blank was $10 and something (the blank was $5 and something) Shipping on 4 of them was almost $14. I really can't see paying that much in shipping for 4" of 3/16" drill rod. I am wondering if there is somewhere I can get it in longer lengths and just cut it myself?
>Have you checked with ENCO. the shipping might be high but I bought my last 3 foot section of drill rod for less than $1 if I remember correctly. Is this 3/16 round rod or 3/16 square HSS bits. If it's 3/16 HSS square I believe I have some I will send you. I'll have to look and see if I have any left. I bought 10 the last time I ordered and got them really really cheap.
>The easiest way to cut a piece of HSS from a rod is to grind a V around it. I use the corner of the grinding wheel. Then put it in a vise and snap it off. CAREFUL, WEAR EYE AND FACE PROTECTION. Then grind it to shape.
>Carole, Don't know if this is any use to you for tool making.
http://www.dixiepins.co/prod_hub.htm
Look at the Dixie pins, they come in every size, I have been going to ask if the toolmakers here if this stuff would be good for things like 3 point tools and what evers?
They also have metric end mills that might be of some use to pen men.
>Carole, the stuff you're looking at in 36" lengths may not be hardened. If it says somewhere "in annealed condition", they are not.
Here's what you need, fully hardened M2 HSS drill blanks--enter this number in the search box:
3009A123
You can't cut this with a hacksaw, need a cutoff wheel which you can get for a Dremel, or for a 4 1/2" angle grinder, even a skilsaw. It's a thin, reinforced grinding wheel for cutting hard materials. The different types and sizes are available at most good hardware stores.
You can also just notch it on the corner of the wheel of your shop grinder, and snap it apart.
>Ken, the stuff I was looking at is 88995K17. What does annealed mean? Why is this so much more expensive than the part# you gave me? What does it mean when it says M2/M7 (the part you gave me)?? I thought it was either M2 or M7. I'm feeling like an idiot just trying to get some simple drill rod to make bits with! All this steel grade stuff is confusing. :(
>Carole, the 3 ft. rod is actually cheaper per inch, but I found out that it is much softer than the short drill blanks I pointed you to which are 3 1/2" long. Took me a little time to figure that out, but the hardness of the two products are measured on different scales--Rockwell B100 for the 3 ft stuff, and Rockwell C64 for the other. C is used for hard tool steels, and B is for softer, anealed (unhardened) steels. Now, to really confuse you, the higher the number, the harder the material. But these are different scales, and if you take a look at a conversion chart here:
Enter 01102128 in the search box, select "MSC Part #" for the keyword. Here the price is comparable per inch to the 3 ft stuff, but in 3 1/2" lengths and identical from what I can see to what McMaster-Carr has.
>Carole, three sources you should always check for tooling needs are:
www.use-enco.com
www1.mscdirect.com
www.mcmaster.com
The three prices I quoted in the title line are for your 3/16 drill blanks (not drill rod) from these three sources. The stock numbers respectively are:
>I deal with the sources listed above. I have found their shipping charges to be most reasonable. The only time the shipping seems to be expensive is when I place very small orders, which I avoid by combining orders as much as possible.
It would seem that a very small item like a tool bit could just be put in an envelope and sent first class for 37 cents, but these companies are not geared to function that way.
Too bad I don't have any in that size, or I would just send you a couple.
Incidentaly, ANNEALED HSS was mentioned above. This is not a good material for us turners. The hardening process for HSS is beyond the capabilities of a home shop, and commercial heat treaters have minimum charges that would make it economically impractical. Tool bits are already hardened and can be ground to shape, so they are a better material.
Drill rod is another story. Both O-1 oil hardening and W-2 water hardening are easy to work with. W-2 is a little harder as it comes from the mill, and for smaller tools can be used as is after grinding. Hardening only requires a propane or MAPP torch. However, for a hollowing tool HSS is the right choice.
It means that the steel is soft. Soft steel can be milled, bent and otherwise machined to the desired shape and size. Once the steel is machined it needs to be hardened and then temper so the hardness and edge holding properties we admire in HSS can be realized. Once the temperature is reached the steel is quickly cooled (some HSS is air cooled, some is water cooled, some is oil cooled I imagine that there is some HSS which is specified to be cooled in some other way) which yields a very hard but brittle steel. The temperature required to harden M2 steel is beyond the normal home shop to achieve. Tempering requires a specific sustained heat followed by a slow cooling to reduce the brittleness of hardened steel. If you temper the steel at to high a temperature you could end up with an annealed form of the steel.
We prefer not to use files for turning tools because files are hardened but not tempered (or at least not tempered very much).
All you need is O1, it comes anealed, (soft). so you can cut it with a hack saw, them you have to harden it,heat it to red and quench in peanut oil, clean it so it is shinny again and then temper it by heating to dark straw, (just before the purple) and quench in water. Voila!
I just did all that today.
My suff is dril rod, round.
How much you need? I have more than I need. Let me know.