Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Motor/Wiring question about new/used lathe

Posts

Motor/Wiring question about new/used lathe

#1

Motor/Wiring question about new/used lathe

Marym

>Hi all,

We took apart our newly acquired Powermatic 90 lathe today, and found an interesting surprise. The motor is labelled as a 3 phase, and seemed to be wired as such in the motor enclosure.

However, when we looked at the lathe running at the shop we bought it from, it was wired as single phase 22O volt at the starter.

Is it possible that the motor is not 3 phase, even though it is labelled as such? The lathe is older, from the sixties, and it came out of a high school wood shop.

Is it possible that they used a 3 phase motor somehow on this machine, and there is some sort of converter in the headstock where the speedchanger is located?

The wiring of this machine intrigues us, and now we are really confused as to how this is set up, or supposed to be set up.

Lastly, does anyone here know if there is a way we can obtain an owners manual for this machine, which might provide more insight on the wiring? The cord that feeds the motor from the headstock is dry rotted, and will need to be replaced.

I will post this on the turning forum as well.

As always, thanks for your help!

Re: Motor/Wiring question about new/used lathe

#2

Re: Motor/Wiring question about new/used lathe

TD

>For info on the PM90 you might try Redmond Machinery in Atlanta.

If the motor says it is 3ph then it is 3 ph. It could have been running on an inverter mounted elsewhere (I have one in my shop). If your machine is equipped with a 3 ph motor then all you need to buy is an inverter with variable speed capability and then you will have a much better lathe than were it single phase. The motor that is in the lathe now will not be inverter duty rated but it will last a good while under normal use (I am told).

TD

Re: Motor/Wiring question about new/used lathe

#3

Re: Motor/Wiring question about new/used lathe

Marym

>TD,

Thanks for the reply. If it was run on an inverter elsewhere in the shop, would the feed to the motor starter on the lathe only require 2 leads? I am unfamiliar with inverters, so please excuse my ignorance.

I guess I just dont understand, if the motor starter on the lathe only had single phase 220volt power feeding it, how can the motor run if it were three phase, unless there is an inverter built into the lathe, which doesnt make sense to me that it would? With an inverter, wouldnt you still need 3 leads feeding the starter?

Thanks again!

Re: Motor/Wiring question about new/used lathe

#4

yes

TD

>a 3 phase motor must have 3 wires feeding it.

Re: Motor/Wiring question about new/used lathe

#5

Re: Motor/Wiring question about new/used lathe

JKJ in East TN

>Marym,

I don't know about the PM, but the motor on my Jet 1642 is labeled as 3-phase on the plate. However, it plugs into a 110v outlet. I believe the variable speed control supplies the proper voltage, current, and phasing.

JKJ

Re: Motor/Wiring question about new/used lathe

#6

Re: Motor/Wiring question about new/used lathe *LINK*

Rick R

>Hi,

This is interesting, since I have been playing with 3 phase motors and single-to-three-phase converters lately.

To make sure I understand this correctly:

- You have 2 wires (plus ground) from the wall plug to the lathe

- There are three wires (plus ground) from the starter to the motor

If that is correct, then you have a 3-phase motor running from a single phase supply. There are several ways to do this, including the VFD method that TD mentioned, although I doubt that you could hide a VFD in the headstock, nor would you want to hide it since that would be a great selling feature.

The simplest and most compact way to do this is to generate the third phase with a capacitor that acts as a start capacitor, but is left in circuit as a run capacior once the motor is started. Such a capacitor could be easily hidden in the headstock.

See the link below under "Self Starting Converter". Click on figure 7 for a diagram.

Rick


http://www.metalwebnews.com/howto/ph-conv/ph-conv.html

Re: Motor/Wiring question about new/used lathe

#7

Re: Motor/Wiring question about new/used lathe

Marym

>I posted this same question on the regular messageboard, and Gene Gauss posted a reply...he says that it is the speed control on the lathe that outputs to a three phase motor, so maybe this explains it- single phase input to the speed control, outputting to a three phase motor.

Re: Motor/Wiring question about new/used lathe

#8

Re: Motor/Wiring question about new/used lathe

Marym

>Hi Rick,

Thanks for your reply. Yes, there is 220v single phase power in. Then, there is a cord running up into the headstock, then another cord running down to the motor. The cord running to the motor is wired in to the motor as a three phase motor, and the cord being used only has 3 conductors, so they used the green conductor as the 3rd motor lead.

We havent opened up the wiring in the headstock to see what was in there, but we didnt think there was much as there isnt much room in the headstock for electricals. The lathe has a large rotory speed control handle on it, and it works pretty nice.

Keep in mind this lathe is about 30 years old, so the technology of the wiring is from that time period. In fact, the motor supply cord is really dry rotted, and needing replacement.

Thanks again for all the help here!

Re: Motor/Wiring question about new/used lathe

#9

Re: Motor/Wiring question about new/used lathe

Walter Ahlgrim

>The old shop could have been wired grounded leg delta all 3 phases and earth ground done with only 3 wires. And the switches need open the 2 hot wires. The things the code use to allow, just to save a little copper.