Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Woodcraft 4" steel faceplates

Posts

Woodcraft 4" steel faceplates

#1

Woodcraft 4" steel faceplates

Craig Daymon

>I'm looking to get a couple of additional faceplates for my lathe and looking to spend as little as possible for reasonable quality. Ideally, I'd like a 4" and a 6". Looks like OneWay has the best deal for a quality 6", but I found 4" steel faceplates on the Woodcraft site for $29 each (8 mounting holes) which is just slightly more than half what most other places want for 4" faceplates.

Anyone using the Woodcraft faceplates? Any comments good/bad? Anyone know a good place to find good deals on 6" faceplates?

Thanks,

Craig

P.S. My lathe has a 1.25"x8TPI spindle. (Luckily, this helps make the Woodcraft plates more affordable, no adapter necessary.)

Re: Woodcraft 4" steel faceplates

#2

Re: Woodcraft 4" steel faceplates

Tony Reynolds somewhere near Newark, OH

>I have several of them and really like them.

Tony

Re: Woodcraft 4" steel faceplates

#3

Re: Woodcraft 4" steel faceplates

Albertabob

>I just bought an 8" here at Busy Bee for my 1/1/4' x 8 tpi lathe for

$19.95 CDN + adapter $8.95

Assuming they are comming from the same "place" that's quite a spread.

bob

Re: Woodcraft 4" steel faceplates

#4

Re: Woodcraft 4" steel faceplates

Craig Daymon

>Wow! Nice price! I'd prefer not needing an adapter as I'd be using a large faceplate for large pieces and an adapter adds one more point of potential failure, but those prices are VERY good.

Does Busy Bee accept orders from down south? (U.S.) Are they on-line?

-Craig

Re: Woodcraft 4" steel faceplates

#5

www.busybeetools.com

Garrett in Victoria

>

Re: Woodcraft 4" steel faceplates

#6

What size faceplate for 20" diameter turning?

Craig Daymon

>OK, maybe this is the better approach. Those Woodcraft faceplates look pretty nice. (Of course, I've visited several sites on this hunt that have well machined plates in the picture with a description that doesn't match.) Will a 4" faceplate suffice for a 20" turning? I was thinking 6" would be more of a safe minimum.

Thanks,

Craig

Re: Woodcraft 4" steel faceplates

#7

Re: What size faceplate for 20" diameter turning?

Roger

>Craig,

Check out www.fredwilliamson.com. When you get to his site, click on making bowls. Fred makes a living turning bowls some in excess of 20". He uses home made 4" face plates, on two home made lathes. Check out the rest of the site while you're there, you'll be glad you did.

Roger

Re: Woodcraft 4" steel faceplates

#8

Steven Antonucci

I've spun 22" 110# oak bowl on a 3" ...

steve antonucci

>Once it was round. I probably roughed out on a 6" faceplate, since it's the only other one I have.

Steve

Re: Woodcraft 4" steel faceplates

#9

Re: What size faceplate for 20" diameter turning?

Craig Daymon

>Thanks Roger, looks like an interesting page. That's one BIG toolrest he has on the lathe!

Looks like a home made indexer as well.

-Craig

Re: Woodcraft 4" steel faceplates

#11

Re: Woodcraft 4" steel faceplates

Gary Evans Tallassee, TN

>Hi Craig,

The best prices I've seen on faceplates were at Grizzly.

I can't speak to their quality, though. Perhaps someone else can.

Gary