Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Domestic, Figured & Live Edge Hardwoods in Stock. Best Prices for Serious Woodworkers.

#%$#@* Spray Lacquer

Posts

#%$#@* Spray Lacquer

#1

#%$#@* Spray Lacquer

David Breth

>I could use a little assistance from the crowd. My experiences with spray lacquer are few and far between because the stuff stinks up the area you use it in and because my results are always not great.

Last night, I sprayed a couple of stickpens (poplar). Followed the instructions letter perfect I believe. Pens were mounted standing upright on a little contrivance I made so I could spray, then spin a quarter turn, then spray, etc., until I completed a revolution. I stayed about 10-12" away, like the instructions ask, and was careful not to overdo it, but just stayed on a side until it looked uniformly wet. I was actually concerned because when I was done, gobby drops were forming at the bottom of the pens.

This morning I took a look, and was not surprised to see terrible results. The surface is rough - stubbly. Fortunately, the globby drops at the bottom are gone - either soaked in or fell off, who knows. But, my results are always stubbly with this stuff. last time, I over-compensated and glopped the heck out of a bowl with the stuff and got pools in the bottom of the bowl.

Can you help me with technique here? I'm pretty sure I'll have to sand a bit before a second coat, which basing on history, will also be stubbly. I can't sand too much, because I've got rub-on decals on the pens.

Annoyed. This is one of those things that make you feel incredibly incompetent because the rest of the world seems to have an easy time of it, and here you go. Its the clumsy part of puberty all over again. But - that's the beauty of this site. There are people who have walked in these shoes, they're out there, and using spray lacquer.

By the way, I can't recall the make, but I think it is pretty decent stuff. I want to say 3M...not sure.

David B.

Re: #%$#@* Spray Lacquer

#2

Re: #%$#@* Spray Lacquer

JanManuel

>I've had way better success spraying lacquer with an airbrush than I ever did using the aeresol cans. A simple, single action airbrush is all you need. The canned Deft is too thin, even a light coat tends to drip.

I use Deft most of the time. Thin it about 2/3 Deft, 1/3 acetone. The acetone evaporates so fast, much of it is gone before the Deft lands on the wood so the it's thicker to start with when it lands on the wood.

I've sprayed projects up to the size of a small table with the airbrush with good results.

Re: #%$#@* Spray Lacquer

#3

Re: #%$#@* Spray Lacquer

RussFairfield

>Probably too much. You tried to do it in one coat. The aerosol cans take many light coats because they are mostly thinner.

What was the shop temperature last night. If it was below 65F you will have problems with lacquer in the spray cans. Lacquer in a airbrush is a little more tolerant of lower temperatures, but not much.

Re: #%$#@* Spray Lacquer

#4

Re: #%$#@* Spray Lacquer

David Breth

>Temp was just under 70 degrees.

Re: #%$#@* Spray Lacquer

#5

Re: #%$#@* Spray Lacquer

Barry Turner

>I don't know what kind of lacquer you are using, but you might want to try Deft. If you don't have a spray gun, try a spray can. Deft has one of the better nozzles for a spray can. Spray on several light coats, rather than a heavy one. After the first coat, sand lightly with 320 or 400 grit. That will act as a sealer and help to take care of the "stubbies". If this still doesn't give good results, you might want to try one of the friction finishes like Myland's or Crystal Coat.

Re: #%$#@* Spray Lacquer

#6

Re: #%$#@* Spray Lacquer

Mike Schwing from Md.

>Aerosol can delivery of common lacquers is always somewhat disappointing. That is not to say showroom results are not possible, as they are, but with much work. A $5 spray gun, which is what you have with your aerosol can, cannot hope to match a well built spray gun. A real spray gun can compensate for viscosity differences as well as environmental conditions and job requirements. Your $5 spray can is a compromise that will deliver the finish to a variety of enviornments acceptably but not wonderfully to any.

Because of this, overspray and drips are common. You must learn to build the coats slowly, very slowly, and accept that unless you are willing to sand and polish by hand, you will never see that perfect finish for which you are hoping.

Since you are concerned about rubbing off the decals, I would suggest spraying on several coats and letting it build, even though disappointing. I'd then use the finest abrasive that I could get away with to rub the finish down flat. Start with LIBERON steel wool. If it works, great. If not, you may have to use something a bit more abrasive. When you have the surface flat and dull, spray another few coats. Then flatten again and do the same till you are happy with the build. Let it harden for a week or more then rub and polish it out to your satisfaction. Many folks wet sand their lacquers up to 12,000 grit to get that scratch free gloss you're looking for.

This is not the preferred method for lacquer, for sure. Each fresh coat slightly dissolves the previous and forms a bond, making scuffing/flattening unnecessary from a bonding standpoint. Waiting too long between coats interferes with this, and rubbing it out shouldn't be necessary, really. But in reality, with a $5 spray can, it is.

You may have better luck with wiping a finish, even lacquer.

Also, you should be wearing a vapor mask, and if you're shooting this stuff indoors, realize it is an explosion hazard around electrical equipment (fans, etc) not designed for such conditions.

Re: #%$#@* Spray Lacquer

#7

Re: #%$#@* Spray Lacquer

David Breth

>Thanks all for the responses. I'm figuring on following Mike's suggestions, then steeling my nerves and waiting a while before I improve the equipment and try again on something else.

I am using this indoors, by the way, am using away from electrical/combustible stuff, and am wearing a vapor mask - north 7700 that is working extremely well.

David B.

Re: #%$#@* Spray Lacquer

#8

My experience

Dominic Greco in Richboro PA

>David,

I've been using spray lacquer on my pens and bottle stoppers for the past couple months now. Before that, I had my troubles with lacquer! So I can feel your pain.

Presently I use Deft Satin Spray lacquer. The first trick is to sand to about 300-400, and seal coat the pens first. Shellac, or even thinned lacquer works great as a sealer.

The second little trick is light, even coats. Like Russ said, Deft in a can is way thin. Multiple light coats do the trick.

I'm glad I took a look at this thread. I've been meaning to try out an air brush for some time now. My sister has one she says she'll give me. Now I have another excuse to drop on over to her house!

See ya around,

Dominic

Re: #%$#@* Spray Lacquer

#9

Re: #%$#@* Spray Lacquer

Eaglesc

>I beg to differ with Mike.

On a pen I recently made I tried Deft spray because of poor results in the past using a wiping method.

A better term for application would be "mist" and it will take multiple applications.I "mist" with high gloss and run through all the micromeshshes.9 grits.

The finish on this pen IS showroom.

applying a "quality showroom lacquer finish takes time, but is worth it.

People are too much of a rush and want instant results.

This pen was sprayed on the mandrel as many as 12 coats, remember the lacquer itself acts as a grain filler.I suspect from the results you described you were trying to do it all at once.


img

Re: #%$#@* Spray Lacquer

#10

I don't see where we differ

Mike Schwing from Md.

>I think we said the exact same thing - showroom finish is possible but not without extra work. Where's the rub?

Re: #%$#@* Spray Lacquer

#11

The big update

David Breth

>Last night, after I finished a turning session and the dust had cleared, I took another shot. More or less a cross between suggestions from above. The pens had been sanded to 600 grit (my finest) before lacquer the first time. I felt the coating I had on them was thick enough to sand them smooth...er without destroying the decals, so I hit them a little bit with the 600 to smooth them out. Reapplied, anticipating that I would wake up today and they would need additional coat...s. I was never really trying to get a perfect coat after one shot, but I was expecting the first coat to at least be smooth - that's what really concerned me earlier. Anyway...here's the rest of the story.

Tough night. I'm a night owl, got to bed about 3am. 3:30, toddler is whimpering in the hall. Nightmare. 4:00, toddler is asking me if it is ok to flush the toilet because she just went tinks. 4:45, infant is awake and screaming, and I told my wife I would take his next wakeup no matter when it happened because my wife had been up pretty late as well. 7:10am drag me out of bed for work. 7:11am, head downstairs just for a larf at my pens.

And wouldn't you know it, the blasted things look great. Now, they aren't showroom hundred dollar beauties, but they are just stickpens for an 8-year old and a 5-year old, and they are easily good enough for that. Clear, smooth, even - I'll buff them out a little bit but I think I'm basically done. At least it was a nicer morning than night.

Daddy needs a nap. A big giant nap.

Thanks again for all the help! I still have anger issues for lacquer, but at least I know I can deal with it.

Re: #%$#@* Spray Lacquer

#12

Re: I don't see where we differ

Eaglesc

>Any good finish is going to take"extra work" there is no lasting panacea.

Take a look at krustal coat after a day or two.

Re: #%$#@* Spray Lacquer

#13

This may work...

KurtK in Indy

>Hi David,

I'm not certain about stick pens, but when I turn my fountain pens and designer pens, I leave out the guts and actually dip the turned upper and lower tubes in a mason jar full of satin lacquer. I use Deft. I have found that the lacq will cover very well and I usually dip them 3 or 4 times in the course of a couple days. I use a length of wire that I make a sort of ball at the end and jam that into the tube. I then just dip the tube and hang them to dry. After a day or 2 of curing, I then assemble the pens and the finish is usually very nice. Of course I sand and then Micro Mesh the pens to 12000 prior to putting on a friction lacquer finish (mylands)while still on the lathe.

This works very well for me.

Kurt