Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Build it. Rock it. Rockler has your woodworking tools.

How about some track lighting?

Posts

How about some track lighting?

#1

How about some track lighting?

Mike Schwing from Md.

>I need to very seriously improve my lathe lighting situation. I have a couple of the flexible Moffat lamps, and I like them for their versatility, but I need more overall lighting. I'd like to get rid of the flourescent fixture above the lathe for all of the reasons they're generally a no-no - disorienting, hard to discern details/sanding scratches, etc.. and would like to provide some directed lighting options. I keep thinking "track lighting", and Lowe's has a good assortment at attractive prices. Some of them are even hung on flexible shafts and could be contorted to provide lots of lighting options on a whim.

In my mind I'm adding a strip on the ceiling on either side of the lathe, extending a couple of feet past the end where I slide the headstock to work on bowl interiors.

I'm figuring a well covered lamp at a min to prevent shavings catching fire and all, and probably those little spot halogens are too hot and too spot specific.

Any comments good or bad? Much appreciated.

Re: How about some track lighting?

#2

Re: How about some track lighting?

Jennifer@Indy.USA

>I have a track above my lathe.....while they get don't get used when the gargae door is up....I do love them when the cold weather sets in and the I'm turing with the door down. I forget how much I like them until winter comes :)

Hey Mikey,Try em! You'll Like em!

Jen

Re: How about some track lighting?

#3

Re: How about some track lighting?

Tony - Memphis

>I've been considering doing something along those lines for my wife's "studio." The prices are really quite reasonable. Her work room is lit from an overhead center light, so its not good for sewing or painting.

Tony

Re: How about some track lighting?

#4

Here's what I did

Mike Cunningham (Cape May)

>Mike

I bought an overhead light that has three heads and mounted it from the ceiling using a length of pipe to get it just above the lathe, I use floods in this. I also drilled and tapped my headstock and mounted an articulated arm lamp, also with a flood. Last I have a third device that has three heads sitting on a shelf at the tailstock, also with floods. The light on the headstock usually provides all that I need, however at times I do want/need a bit more and turn on the three head overhead. The unit on the shelf I use to illuminate the interior of bowls. On top of this are two 2-tube 4' florescents on the 10' ceiling over the lathe area.

Lots of light, no shadows.


img

Re: How about some track lighting?

#5

Dentist Light

Wayne Cooper Charlotte NC

>Mike

The last time I was sitting in the dentist chair, I was admiring the light he used to see into the dark cavern of my mouth. It is extremely flexible, bright and cool in the summer. He arranged for me to get a used one that came out of someones dental office. The next time you are in the chair,imagine how great that light would be over your lathe. Wayne

Re: How about some track lighting?

#6

Re: How about some track lighting?

William Duffield, on the Cohansey

>I would be more than a bit concerned that wet wood shavings would get up into the track and short circuit it. Over the lathe, you need to be very careful that all your wiring is carfully enclosed. Exterior, sealed boxes and conduit wouldn't be a bad idea.

Re: How about some track lighting?

#7

Dick Hines

Re: How about some track lighting?

Dick Hines

>I have the same proublem as Jennifer, a gargae door. SOOOO I mounted spot lights on the wall behind the lathe. I also use some of those cheap clamp on lights that painters use. I clamp them on the gargae door tracks.

Re: How about some track lighting?

#8

Mike. that's what I have.

Thomas Skaggs, Foothills of Mount Level

>Mike,

I have sung the praises of track lighting for years. I installed tracks over my work benches and some tools and I love it! I don't use low voltage. I use the standard PAR 90 lights and cheap fixtures. I can add, move or re-direct them as I wish. They flood my work areas with light...including my lathe!

Do it!!

Tommy

Re: How about some track lighting?

#9

Re: Dentist Light

Fred in NC

>I have looked all over for dental/medical lights. No luck !

Re: How about some track lighting?

#10

Re: Dentist Light

RK in Milw

>Just do a Google search on Dental Equipment. There are used equipment dealers listed. Those babies aren't cheap. About $900 for a wall/ceiling mount unit. RK

Re: How about some track lighting?

#11

Re: Dentist Light

Fred in NC

>That is what I did, and exactly what I found. I could buy a lathe for that much.

Re: How about some track lighting?

#12

Re: How about some track lighting?

Lowell Converse

>IF there is an attic or access above your shop, recessed lighting works great. Halogen FLOODS spread the light. And in the winter here in Ohio it helps keep you warm!

Re: How about some track lighting?

#13

Re: How about some track lighting?

The Wood Spinner / Bill Hale

>I have even posted here about the danger of the halogen BUT.

I use them in the 500 watt size but put them high on the wall away from the flying curls. I also take off the wire shield to prevent holding any shavings that may get up there. I also use the par flood and spot lights. I find with lights in several locations I can do a better job of contouring.

I also have a 500 watt halogen no cage, mounted low on a movable stand, that I can set to shine in to the work.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: How about some track lighting?

#14

Re: How about some track lighting?

Bill Neddow

>This gives new meaning to the words "track lighting"!

Re: How about some track lighting?

#15

Re: Here's what I did

Carole in VA

>No need for heat in your shop, Mike...you might just roast yourself with those lights! LOL

Re: How about some track lighting?

#16

Re: Dentist Light

Earl Eyre

>Have you asked your dentist? I mentioned it the last time I was getting my teeth cleaned and the hygienst said "we have an old one laying in the store room and we just set another one--complete with chair--out by the dumpster." The chair and light by the dumster were gone the next morning. She asked the dentist about the one in the store room and he said, "Take it. If the lamp doesn't work, just let me know, I have a whole box full." Whenever they modernize, the old ones are the first to go. I haven't even set it up yet, but will when I get around to it.

Earl

Re: How about some track lighting?

#17

Re: Here's what I did

Mike Cunningham (Cape May)

>Carole,

You're right, if I turned all of them on together,there'd be no need for any other heat source. 90% of the time I use just the single bulb unit off of the headstock. The 3 bulb overhead is a great aid in sanding or for something very small and detailed. The unit at the tailstock is used, like the single bulb unit, mostly on it's own, to illuminate bowl interiors.

Across the shop I have a three bulb track light unit, like others have talked about, over my bench. It's up at the ceiling height and bathes the bench in light. With the lathe lighting I wanted to be able to get a brighter more intense light if needed. I can also unscrew one or two bulbs in the three-bulb units as well.

Re: How about some track lighting?

#18

Re: How about some track lighting?

Jill

>Hey Mike, I use them as well. I bought mine from the HD clearance table for $4 a piece (the bulbs cost more!). Making a stand right now that will allow me to move the stand when I move the lathe. I am using 1x4's on the sides and top rail. Yep and it keeps you warm. "-)

Re: How about some track lighting?

#19

Re: How about some track lighting?

JKJ in East TN

>>Halogen FLOODS spread the light. And in the winter

>here in Ohio it helps keep you warm!

Yikes, what about the summer? (Oh, I forgot, the summer in Ohio only lasts 4 days.)

I have 7 or 8 lights in reflectors around my lathe and ended up replacing some of them with bright fluorescents which are much cooler. I haven't noticed any strobscopic effects. After being reminded by your post, I think I switch back to hot lights for the winter!

JKJ