Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Fitting a new spindle adapter in a Talon Chuck

Posts

Fitting a new spindle adapter in a Talon Chuck

#1

Fitting a new spindle adapter in a Talon Chuck

Craig Daymon

>I'm trying to put a different spindle adapter in my Talon chuck so I can use it on the new lathe (which finally has power and is fully assembled) but I can't get the old one out. I took out the three screws, so that's not the problem. It seems to be just VERY well seated thanks to the taper fit and won't come loose. I don't want to damage the chuck trying to do this, so I thought I'd ask for some advice.

Thanks,

Craig

P.S. I have tried tapping on the insert with a large allen wrench, but that didn't do anything.

Re: Fitting a new spindle adapter in a Talon Chuck

#2

Re: Fitting a new spindle adapter in a Talon Chuck

Rick Allen

>There are two holes in the adaptor which are threaded. Put two of the screws in there to apply presure to remove the adoptor.

Re: Fitting a new spindle adapter in a Talon Chuck

#3

Re: Fitting a new spindle adapter in a Talon Chuck

Craig Daymon

>Thanks Rick.

-Craig

P.S. Very nice "Dot" bowl.

Re: Fitting a new spindle adapter in a Talon Chuck

#4

Re: Fitting a new spindle adapter in a Talon Chuck

Ronny Eelen (from Belgium)

>Is that so??? I had to resort to force and a hammer and big screwdriver, just a few weeks ago. Should have asked it here.

Re: Fitting a new spindle adapter in a Talon Chuck

#5

Re: When all else fails..........

RussFairfield

>Read the directions.

(Sorry, couldn't resist) {8>)

Re: Fitting a new spindle adapter in a Talon Chuck

#6

Re: When all else fails..........

Craig Daymon

>None were provided in the box with the new adapter and I don't know where the old instructions might be at this time, for either the chuck or the original adapter. Besides, as familiar as I am with the meaning of RTFM since I am a programmer, it doesn't always help. My new 3520A has a Delta (not the Norm sponsor) inverter on it. It has a control panel that has several controls and a digital read-out, but the manual includes NO description of how these controls are used or of the unit itself. The digital read out is also on the opposite side of the lathe to be of any use when the lathe is in operation. Thank goodness for Google.

-Craig

Re: Fitting a new spindle adapter in a Talon Chuck

#7

Re: Fitting a new spindle adapter in a Talon Chuck

Bill Grumbine (Kutztown PA)

>I sort of went through this when I was buying my Stronghold lo these many years ago. I had called Oneway and was talking to Kim, the owner's daughter. I asked her how I was supposed to get the adapter out of the chuck to switch it over to a different lathe.

"It's easy," she said, "you just use the jack off screws."

"The WHAT!?!", I asked, somewhat taken aback.

There was silence on the phone for a few seconds. I could hear her turning red on the other end of the line. After a few more seconds passed, she stammered out an explanation with a lot of umms, ahhs, and stutters. I have no idea if anyone ever got that description again, but I sort of doubt it.

Bill

Re: Fitting a new spindle adapter in a Talon Chuck

#8

Dick Hines

Re: When all else fails..........

Dick Hines

>Make sure ALL the screws are loose. Then put the adapter in a vice. Take a steel bar and chuck it up in the chuck. This will give you a lot of leaverage. Does not hurt to spray some WD40 in the adapter and let is sit for a while.

Re: Fitting a new spindle adapter in a Talon Chuck

#9

Re: When all else fails..........

theeviltwinn

>Dick, you are kidding? right?

If you use the two jack screws like the instructions say, the adapter pops right out.

Or you could put the chuck on the floor and beat it with a sledge hammer until the adapter comes loose.

Craig, the controler on the PM is on the backside of the lathe to keep people like me from messing with it ;-) See you at Bucks

Mike

Re: Fitting a new spindle adapter in a Talon Chuck

#10

Re: When all else fails..........

Craig Daymon

>I can hardly say it "popped" out, but it did eventually come out. I did think I was going to snap an allen wrench or strip a screw head, but it finally gave.

I called Powermatic tech support about the controller panel on the inverter and they really didn't have any more advice except to try the Delta Electonics web site. I did, but I haven't read through the 250 page manual I downloaded for the device. Unfortunately, the digital display on the inverter doesn't show RPMs, even though the number does increase as RPMs increase. (Maybe it is and it is just prior to gearing?) I'll try to dig in a little more and see if I can find something useful that might "enhance" using the lathe.

Mike, did you say you built your own indexer for the Powermatic? What plans did you use?

Thanks,

Craig

Re: Fitting a new spindle adapter in a Talon Chuck

#11

Re: When all else fails..........

theeviltwinn

>Wow. Yours must have been really tight. Mine comes out easily when needed. I just keep adding pressure alternating between the 2 screws until it comes loose. Maybe you should check your adaptor and chunk body for damage- scratches or grooves and the like.

The OM says the controller comes pre set from the factory and you shouldn't mess with it. There is a chart in the back of the manual that shows the controller reading and lathe speed. I checked and the postion of the speed knob gives me a close enough speed. ie when the knob is half way between all the way off and all the way on the lathe is running at about 600 rpm in the low range- half way between 0 and 1200. A 1/4 turn is about 300 rpm and 3/4 turn is 900 rpm. I turn by feel anyway and don't worry about the exact speed.

I haven't made an index system for the PM. I use Bill Smith's system on my Jet and will do the same when I need indexing on the PM

Mike

Re: Fitting a new spindle adapter in a Talon Chuck

#12

Re: When all else fails..........

Craig Daymon

>Perfect. I just downloaded an assortment of his indexing templates.

I do tend to overtighten things like this. I suspect that now that the PM adapter is installed, it will stay installed. I have a cheap $40 chuck for the mini that I may upgrade someday to the smaller Axminster, which works on a key instead of those awkward jimmy bars (so it doesn't require 3 hands).

I hope I haven't fiddled with any of the settings. I think that should be a big red letter warning in the front of the manual (or on the cover). All those controls that look like they might apply to lathe operations should be better guarded if they are not to be touched.

Thanks.

-Craig