Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Finally got some work done

Posts

Finally got some work done

#1

Finally got some work done

Mike Schwing from Md.

>Finally! Been more than 2 months since I turned on the lathe. This past weekend I finish turned 3 pieces that had been sitting on the drying shelf for long enough.

The first is in this post. It is a piece of white ash that has been drying for about 3 years. Was in fact the first tree I ever cut up with a chainsaw for turning lumber.

It is about 8" wide, and I'm very pleased with the form but I wish I could have tucked the bottom in a bit more. I was afraid of running out of bottom, as I'd turned a few of my recent bowls to zero bottom thickness. There is no finish on the outside and a coat of wax on the interior for a bit of contrast. All comments welcomed.


img

Re: Finally got some work done

#2

Number 2

Mike Schwing from Md.

>Walnut crotch. Made a mistake cutting it up. Cut it across the wrong diagonal. Was hoping for a feather, just had a brain fart with the chainsaw. Turned out OK, but the sloping rim makes it look heavy until it is more closely examined. Finished with clear Briwax after sanding smooth to 4000 abralon. Comments welcomed.


img

Re: Finally got some work done

#3

Number 3

Mike Schwing from Md.

>Lovely piece of ambrosia maple. Very yellow in color, too, with only a coat of clear wax on it. About a foot in diameter, and very nearly a half circle in form. Holes not filled, hope this one doesn't see food use. Sanded to 500 abralon because sanding higher revealed a few sanding scratches that went very deep and I would have either blown the bowl up returning it or messed up the interior profile sanding them out. Comments welcomed. Really glad to be turning some again!


img

Re: Finally got some work done

#4

Re: Number 3

Jennifer@Indy.USA

>Mike, it's great to see you back at the lathe....and turning bowls no doubt! All three are really nice looking pieces. Some times the simple looking ones are the most challenging. Love 'em all!

Jennifer

Re: Finally got some work done

#5

Re: Number 2

Ed Kelle

>Looks really great Mike. This sure is a wild piece or walnut. glad to see you back again!

Re: Finally got some work done

#6

Re: Number 3

George Van in WI

>Welcome back Mike. Good to see some of your turnings again. I�m with Ed on the walnut, lots of character in this one and good volume also. I like the grain orientation and form on the ash; will you apply a finish on the outside?

Where these photos taken in your tent? They show the bowls well.

Re: Finally got some work done

#7

Re: Number 3

John Lucas

>Mike We/re glad your back. I missed seeing your work. Hope the shoulder is OK.

Re: Finally got some work done

#8

Re: Finally got some work done

Ken Grunke from SW WI

>Lovely ash bowl Mike, the bottom looks good to me. But doggone it, I wish you had slapped just a bit of finish on the outside, to make those stripes pop out a little :-)

Ash is one of my favorites, love the sweet peppery smell--don't know how else to describe it.

Re: Finally got some work done

#9

Keith Tompkins

Re: Number 3

Keith Tompkins

>Hi Mike, welcome home! Looks like you got BETTER in your absence! I especially like the ash form...

Re: Finally got some work done

#10

Brad Vietje

Re: Number 3

Brad Vietje

>Nice to have you back, Mike ! Beautiful stuff, as always. I like the form on the Ash bowl especially -- do you plan to finish the ouitside ?

Safe Spinning,

Brad Vietje

Thetford, VT

Re: Finally got some work done

#11

Re: Number 3

Philip Duffy

>Mike, BZ on all 3! Phil

Re: Finally got some work done

#12

Re: Finally got some work done

Bob Hackett

>Why not either lightly sandblast or wire brush the outside of an ash turning?That way you get both the early/latewood definition and alittle texture as well.

Finish optional afterward.

MB

Re: Finally got some work done

#13

Re: Finally got some work done

Bob Hackett

>First,welcome back Mike.

I can sense you`re just tuning up with afew bowls before you let loose with all those ideas you have stored up while you were away.When can we expect pics from the wild side?

Mainely,Bob

Re: Finally got some work done

#14

Re: Finally got some work done

Mike Schwing from Md.

>Bob you're right I am just tuning up, but Mrs. Schwingaling says we've got some bills to pay, or Christmas gifts to give, and the bowls really help to pay the bills, plus they make her happy. Gotta make her happy.

I have to decide which insane idea to attack next. Narrowed it down to 3 choices - a new type of bug, a very "dark" piece of wood art, or something to submit for the 2006 AAW symposium.

Re: Finally got some work done

#15

Add me to the Welcome Home Wagon

Molly Winton

>You've sure been missed around here Mike. Glad to see your work again. The bowls are sweet! I say you make something for the AAW Symposium, that way it'll help ensure you show up! Sure would enjoy seeing you again. My best to Mrs. Schwingaling!

Re: Finally got some work done

#16

Great stuff, Welcome back

Bernie

>

Re: Finally got some work done

#17

Re: Number 2

ken chase

>Mike:

Wish I knew enough to understand your own critique about

cutting it incorrectly. Looks terriffic to me. Like all your work.

Re: Finally got some work done

#18

Turn to the dark side Mike! ;)

Ed Kelle

>

Re: Finally got some work done

#19

Re: Number 2

Curt Fuller

>Can't quite imagin how that could have been any prettier.