Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

REAL MILK PAINT

Correction: Bowl Skew Geometry /Usage

Posts

Correction: Bowl Skew Geometry /Usage

#1

Correction: Bowl Skew Geometry /Usage

Ed Moore

>First, I wish everyone a nice Thanksgiving.

I went to the shop this morning and looked at my bowl skew. I immediately realized that I had incorrectly described the sharpening process in my original post. Mea Culpa. Below you will find the corrected version of that post:

Two years ago at the OVWG Symposium I saw Dave Hout demonstrate the tool and he had each of us try it. Yes, I bought one. Start with a rectangular piece of stock that is 3/8 x 5/8" and grind a flute on the wide side that is 3/16" deep and extends from one edge to the other. Its cross-section is shallower than a bowl gouge and deeper than a spindle gouge, with two vertical sides and a flat bottom.

To sharpen this tool, put it on the platform of your grinding jig, which is at a 6 - 8 degree angle, and sharpen as if it were a slightly rounded scraper. Then, grind a secondary bevel at about 45 degrees so as to remove some of the heel of the first bevel.

To use this on the inside of a bowl, rotate the tool 90 degrees so that the right side is flat on the tool rest. Keep it flat and do not rotate the tool. Adjust the cut by dropping your right hand slightly. Think of this tool as being used to clean up the transition portion between the side and the bottom of the bowl. I regard it as sort of a "tweener". If you extend the tool into the bowl and adjust so that you are getting a cut then the cut will be a shear cut just below the center of the tool. Actually, you should try this with the lathe turned off and rotate the bowl by hand before you just dive in with the lathe on.

From my perspective the tool is better theoretically than it is practically. Possibly it deserves a second chance, but I have sort of moved on. In fairness, it did not produce catches, even though that square edge on the bottom looks like it will grab everything in sight.

Ed Moore

SW VA

Re: Correction: Bowl Skew Geometry /Usage

#2

Re: Correction: Bowl Skew Geometry /Usage

Jennifer@Indy.USA

>Ed, thanks for the information....I'm not sure if I'm the only one...but I seem to be a bit confused (easily done). I would love to see a picture of what you're describing. Could I plead and beg for a couple? Maybe one of the tool and another of the presentation you're speeking of?

Pretty please :)

Jen

Re: Correction: Bowl Skew Geometry /Usage

#3

Me to, pics please

Terry Quiram, Roanoke Illinois

>I asked the question the first time and must admit I am still a little fuzzy on the use. I agree with Jen, pics please.

Terry

Re: Correction: Bowl Skew Geometry /Usage

#4

Re: Correction: Bowl Skew Geometry /Usage

Ed Moore

>Tomorrow I will see what I can do for a picture. I'm by myself in the shop, so I'll have to figure out a way to stage what I am trying to convey to you.

Imagine a letter "C" that is slightly bent with the top and bottom portions a little towards you. Think of it as a branding iron on a stick towards you and you are going to brand a wall. If you hold it straight out and then raise your arm slightly and walk towards the wall, what would touch the wall first? A point near the middle of the "C" and slightly below its center. Now, imagine that the wooden wall is dropping straight down and that the "C" is sharp. You would be shearing off a bit of the wall.

Now, that description is probably about as useful as airbrakes on a turtle, so I'll try to be clever with the camera tomorrow. Then, I must figure out how to post the pictures.

Re: Correction: Bowl Skew Geometry /Usage

#5

Re: Correction: Bowl Skew Geometry /Usage

Jennifer@Indy.USA

>No hurry Ed.....it's a long weekend :)

We're just all so curious!

Thank you!

: )