Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

With Respect to Dennis' mishap below

Posts

With Respect to Dennis' mishap below

#1

Steven Antonucci

With Respect to Dennis' mishap below

steve antonucci

>I noticed that there seems to be a statistical correlation to my own experience. Having turned many hollowforms in my life, the only two places I have ever cut through a side have been the exact same place he did, and at the transition from the top curve to the side wall when undercutting.

I have gotten a lot better at avoiding this, although it is still something that my bad work habits can produce when I do not follow the proper procedure or take short cuts.

Here are the things I do that can greatly reduce this problem.

1.) Measure often with calipers, but do not rely on them as the only means of inspection.

2.) Clear out shavings frequently. As you get thinner and thinner, the shavings will wad up along the walls and can cause the piece to vibrate, which will cause the inner cuts to be uneven.

3.) Use a high powered flaslight to gauge relative thickness. Thin walls transmit light, thick spots do not. If you can see the interior, you will be able to change where you place the cutter, and take light passes with the tool in the appropriate spots.

4.) Best advice I can offer is to switch your cutting tool from a standard 1/4" cutter to a disk cutter with a larger surface. Since the cutting surface is much larger, they tend to cut slower. As an added bonus, they also even out any ridges and leave a much better interior surface.

Hasn't stopped me from ever doing it, but if I follow my own advice, I rarely lose a vessel. Now if I could just find a method for accurately measuring the bottoms between an 1/8" and 3/16"...

Steve

Re: With Respect to Dennis' mishap below

#2

Re: With Respect to Dennis' mishap below

John Lucas

>Steve My friend Randy called and said he had cut through 2 ornament balls in a row and they were cut in almost the exact place that I cut mine in two and those are roughly where you cut your hollow vessel. Maybe there's an excessive gravitational pull at the at point on a hollow vessel.

Re: With Respect to Dennis' mishap below

#3

Re: With Respect to Dennis' mishap below

Gerry in Maryland

>John,

I blew out 2 ornament balls in the same place too. Maybe we should all head to Australia and see if we blow them out on the high side.. LOL!!

Gerry

Re: With Respect to Dennis' mishap below

#4

Below the midline thinning force

David Propst

>It must be due to a force of nature! Almost every bowl I have have ever gone through, or just got thinner than I would like has been in that area.

David

Re: With Respect to Dennis' mishap below

#5

Re: Below the midline thinning force

David Breth

>I'm pretty new to this (still waiting to "celebrate" my first year in January, but I have an idea of what is going on if I'm able to explain it. I've made a few lampshades, and the guilty area of oops I went to thin seems to be the same in my bowls as it is in the subject hollowform and the previous posts on this particular link.

Whether you use your hands or calipers to understand the width of your turning, you have a big problem where the curve begins at the bottom. You can't see where the tips of your fingers or calipers are pinching, so you can't know if they are pinching together in the right place. Say you've got a short cardboard box. You feel the wall near the top, and you can see that if the box weren't there, you'd touch your fingertips together. You slide down the box with your fingers clamped around the wall. There's a point where the inside finger pivots, because the outside finger needs to feel the bottom of the wall, then the outside corner, and finally the bottom of the box, to understand the thickness.

Now substitue a bowl. The "corner" is a curve, and it is mighty tough with calipers or fingers to get a feel for the depth at that curve. You can't tell if you are perpendicular to the surface or not. The bottom always feels fatter, and depending on where you take measurement, you might think you have a ton more room than you actually LAMPSHADE!!!!!!!

Don't know if I explained that well or not, but I think this is the heart of the problem.