Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

A55 Smoothing Plane

OPPS

Posts

OPPS

#1

OPPS

Dennis Bilevich PRESCOTT AZ

>I hate it when this happens. I still have a lot of learning to do with the laser, it got way to thin on final cut. The vessel was willow wood, 14" tall and 8" in diameter, and now is firewood.

Dennis


img

Re: OPPS

#2

JL

Re: OPPS - Design opportunity!

JL

>

Re: OPPS

#3

Steven Antonucci

I smash them on the floor when the lathe stops

steve antonucci

>I've gotten to the point where I don't scream obscenities... half of the time, but I know that you had a few hours into it...

I feel your pain.

Steve

Re: OPPS

#4

Re: OPPS I agree this one is a design opportunity

Jill

>

Re: OPPS

#5

Re: OPPS

Jim King

>Nothing better than a caliper and common sense. Wood turning is a primative art form that has been around for hundreds of years and we all try to make it as we have done something new. If you have the opporonunity just pass thru the Spaniish Royalty Castile or any of the other Capitals of Europe and see where we are in this type of art. We are just about to learn what was done 200 years ago without electricity and the exotic tools we have today.

Re: OPPS

#6

bummer

John Lucas

>Dennis I found the lazer to be a surprise from time to time like you just did. Bummer.

Re: OPPS

#7

We all oops

tek-Brunswick, Ohio

>At least you can claim you had an accident on a technically challenging piece. I just blew up a simple spalted maple bowl a couple of days ago. I just took my last cut on the inside. I got most of the ripples out of it. That was when I made my mistake. I just quit concentrating on what I was doing. I got sloppy taking the gouge out of the bowl. It hit the side of the bowl and slammed down on the toolrest. Bam! Instant jigsaw puzzle. At least I found out I had a nice consistent 3/16� wall thickness. Oh Well, more fodder for the wood burning stove.

Tom

Re: OPPS

#8

Re: OPPS

Steve Roxberg

>Dennis,

I notice you live in Prescott, I visit an inlaw there every other year.

I'd love to stop by and see your shop/studio the next time I'm in Prescott.

Re: OPPS

#9

sacrifice

e

>we are all required to occasionally sacrifice to the wood-gods -- beautiful contribution.

Re: OPPS

#10

Re: OPPS

Barry Turner

>Neat! How'd you do that? Can you do it again?

Re: OPPS

#11

Re: OPPS

georgetroy

>Don't burn it. Take 1/16" parting tool and part off on up towards the budge. After you get real close to the point where it is about to jump off, slow lathe way down. You will then take your cole or button jaws and square off where parted. The neck you have on there now will work just fine to remount. I repart frequently to make thin segmented rings. Try it what do you have to lose!!!!!!!!!!!! Then think of way to make a compote bowl or something else. GT

Re: OPPS

#12

Bummer Dude!

Molly Winton

>

Re: OPPS

#13

Salvage it

Jorge Castaneda ~ Downeast Maine

>Cut it above the boo boo and make a bottom of a comtrating wood, let's say black walnut.

Just an idea

Re: OPPS

#14

Re: I smash them on the floor when the lathe stops

Ruth Niles

>I do the same thing, Steve, right after I hit it with the tool!

Re: OPPS

#15

Re: OPPS

David Breth

>I'm supposed to send something from the lateh to my in-laws for Christmas. If I give you the address will you send that to them?

Re: OPPS

#16

It can be saved!

TD

>Make a belt around it with twine. Just drill a hole below the bad area and insert the end of the twine and put a drop of CA on it to hole in place. Slowly make a revolution gluing the twine in place as you go. After you have one revolution glued in place everything is easy. Just continue wrapping the piece until the hole is gone, er, hidden. A little epoxy paste on the inside, if you can get a hand in there, will finish it off. Of course I have never had to do this :-).

TD

Re: OPPS

#17

Re: OPPS

Jennifer@Indy.USA

>How many times have all of us seen those ugly jagged teeth laughing at us when we stop the lathe....probably most of us who've turned a hollow form. It's gonna happen to everybody. It sure did look like a nice one.

Keep on turning!

Jennifer

Re: OPPS

#18

Re: OPPS

Don Tewell

>Very nice looking firewood. Unfortunetly, we've all done this at one time or another.

Re: OPPS

#19

Re: OPPS

ken chase

>I have had the same problem. Thought that was not supposed to happen if a lazer was used. Good to know.

Re: OPPS

#20

Re: OPPS

Dennis Bilevich PRESCOTT AZ

>Steve email me and i would like you over Dennis

Re: OPPS

#21

Re: OOPS!!

Ed Moore

>While taking a light cut on the bottom of a bowl that was reversed, I rolled the gouge over a little and got a lousy catch. Of course the bowl flew off the lathe and cracked on one side as it hit the floor at Arrowmont. This was on a Friday, so not long afterwards a couple young ladies who work there came through, they spotted the wounded bowl and asked if they could have it. I said "Sure, but why would you want it?" They said that they would cut it in half and mount the good half on a board and use it for dried flowers.

To understand the way they would cut it, look down on a bowl sitting normally on a table and make a vertical cut so that you have a right half and a left half. Put glue on the cut and slap it on a board. Voila', a receptacle for dried flowers.

I was tempted to tell my turning buddies that I had been asked by Arrowmont to leave a piece of my work there. True, but greatly misleading.

I was amused that those gals had figured out that by dropping by the turning venue they would find discarded objects that could be salvaged for craft projects.

Ed

Re: OPPS

#22

Ingenious solution

RevDoug

>You could also use any color yarn to make a contrasting "belt."

Turn 'em round,