Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Premium Live Edge Slabs, Hand-Selected in the Berkshires. Shop Unique Hardwood Pieces.

Between Centers Again

Posts

Between Centers Again

#1

Between Centers Again

W.C. Turner

>Sometime ago, I posted about starting bowls, between centers, these were smaller bowl blanks, 6 inch diamter, or so.

Recently, I've tried larger blanks between centers, about 15" dia., weighing about 21 pounds. I use a dead blow hammer, off the lathe, to pound the drive center into the blank. When I try to mount the blank on the spindle, invariably, the drive center will pop out, or, I have to re-arrange the blank to be more balanced, blank is hard to hold with only 1 arthritic hand, etc. Then, in order to get the blank mounted, I just crank the tailstock live center in, to hold the blank on. I saw John Jordan do it like this in his "Bowl Turning" video. He even said "It wasn't necessary to pound the drive center into the blank". Although, I don't think the one in the video was 20 pounds.

1) How do ya'll get the spur drive center to stay in the blank without it falling out the first time, & without placing unecessary force on the tailstock?

2) This is about the 3rd. large blank I've tried like this. I've noticed a grinding sound(kinda like the sound of my arthritic joint bones grinding together), appears to be coming from the spindle. I don't think I placed any abnormal stress on the tailstock that would damage the bearings. Does this sound like a bearing problem?

Thanks in advance for any replies.

W.C.

Re: Between Centers Again

#2

Re: Between Centers Again

John Lucas

>WC I carve away the bark and cambium layer so the drive center sits better. I use a 1 inch drive center but I really would like to have a larger one for rough bowls.

Re: Between Centers Again

#3

Re: Between Centers Again

adrien

>You can also use a spur bit to clear the bark for the drive center.

Re: Between Centers Again

#4

Re: Between Centers Again

georgetroy

>I pound mine in until it stays. I use a wooden mallet or rawhide hammer. My spurs are very sharp and that helps. I use a live cup center to hold up the end. I crank it down hard. I have a 600 lb. Vicmarc. If possible flaten both ends, especially where to sap wood is. There is no easy way to get that block up there, you just have to horse it up. Some turners have engine block hoists. Showing a pic using button jaws after hoging out the inside.


img

Re: Between Centers Again

#5

Pound the bejesus out of it...

Peter Teubel

>For green bowl blanks, I only use a 2-prong spur drive. I simply wail the spur into the wood (parallel to the grain) with a 7-lb wood "club" (turned, of course). Hey, the wood club can't possible hurt the steel spur! I drive it in a full 3/4". Its in there so tight that after mounting on the lathe, it'll just hang there in the air without the tailstock (yes, I've had 30# blanks hang).

You need a stout lathe to drive the spur into the wood using tailstock pressure alone.

Re: Between Centers Again

#6

Re: Between Centers Again

JKJ in East TN

>I do not like to use excessive force from the tailstock since I think that is hard on the bearings at both ends.

I pound the spur center into the blank with a wooden mallet, then remove the spur from the blank and put it into the headstock spindle. Then I hold the blank up to fit into the indentations and bring up the tailstock. The indentations made from the pounding hold the blank very well. If I don't use this method, the blank often spins on the spur center.

(Actually I usually do one step previous to the above - I mount the blank very lightly between centers on the lathe and move it around as necessary to get it balanced, mark the spots, then remove it and do the pounding. My lathe is not weighted enough to handle a significant imbalance.)

JKJ

Re: Between Centers Again

#7

Re: May I recommend Best Wood Tools?

Al Crandall- NE of Indy

>I use the 2" two spur drive center from Best Wood Tools which I mount in the jaws of my Talon chucks. I believe they also make these in dovetail styles for other brands of chucks. The center doesn't have a tendency to drill into the blank and spin like a four spur center does. It needs no pounding to seat firmly if you aline the spurs with the grain of the blank. The holding and driving power is awesome. Any blank which I can lever up onto the lathe can be driven with this system. If you have't guessed by now, I high recommend it.

Re: Between Centers Again

#8

Re: Between Centers Again

Earl Eyre

>You can also use a chisel to put cuts in the wood where the spurs go. It works quite well and lets the drive sit deep enough that it minimizes it starting to spin in the wood. I saw in a Bonnie Cline video where she actually cuts an X on the bottom with a bandsaw.

Earl

Re: Between Centers Again

#9

Re: Between Centers Again

Dave Peebles Lyons, Ohio!

>Hello W.C.

I think it depends a lot on the lathe you have. I have never pounded the spur center into the wood.

I always mount the wood lightly between centers to get the balance just right, after I feel that the piece is balanced, I just crank down on the tailstock. It seems to work for me on my lathe. It has not caused any damage to my bearings on either the headstock or tailstock in the last ten years. :) I also tend to snug up the tailstock a few turns while I am getting the piece rounded up.

But I have never felt that I was putting any undue stress on my lathe with this procedure.

Best wishes,

Dave

Re: Between Centers Again

#10

Re: Between Centers Again

Norm Smith in Nova Scotia

>Hi Dave,

I use a forsner bit the same diameter, or larger as the spur drive and drill a hole about 1/2" deep or so (depending on the wood surface). I than put the spur drive in and set it with a wooden mallet. Works for me.

Norm

Re: Between Centers Again

#11

Re: Between Centers Again

Ron in Drums PA

>I have a two prong center with a long center point. I use a forstner bit to get though the bark and to provide a pilot hole for a drill bit.

I drill a hole into the blank with a bit that matches the long center point. Then I take a chisel and cut a cross grain notch for the two prongs to line up in. Then all I need to do is tap in the center, align the prongs into the notch, mount on the lathe, move up the tail stock and I'm ready to go.

Re: Between Centers Again

#12

Re: Between Centers Again

The Wood Spinner / Bill Hale

>I do like John.

I have a Oneway 2436 and have put very large pieces between centers and just crank down on the tailstock. I would guess the largest piece was in excess of 90 lbs. I mount the piece. align it to where I want it and crank down. After it is where I have cranked I jog the piece a fiew times and re tighten. Turn down the speed and turn on the lathe , retighten. I retighten several times as I rgh. down.

Never had a piece come out !

Good turning and be safe

Bill in Casa Grande, AZ.

Re: Between Centers Again

#13

Re: Between Centers Again *LINK*

Fred Holder

>Am I the only one who doesn't use a drive center on the headstock? For years, I've used the four jaw scroll chuck with the jaws opened up a bit on the headstock and a cup type tail center, the last couple of years I've been using a Live Steb Center in the tailstock. The chuck that I've been using for this purpose since 2003 has been the Nova 5" chuck with the large jaws. I've never even felt that the piece wanted to come out of the lathe. The mounting seems to be solid as a rock. I can't remember who I saw demonstrating this technique. I tried it and liked it immediately.


Fred Holders Domain