Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Compare cordless drills on the numbers that matter

Ebony Hollow Form

Posts

Ebony Hollow Form

#1

Ebony Hollow Form

Mark Kauder, Phenix City, AL

>4" in diameter, Ebony, Bloodwood and Yellowheart.

Mark


img

Re: Ebony Hollow Form

#2

Re: Ebony Hollow Form

gary s clarke

>Mark, great looking hollow forms, what type of finish on most of them?

Re: Ebony Hollow Form

#3

Re: Ebony Hollow Form

Jennifer@Indy.USA

>Mark, All of these are so fantastic! I love the smaller size of them...I'm kind of into a smallish phase right now. This one though is by far my favorite! It's just lovely. I love the soft edge to the opening...the form...the colors...it's so rich!

Bravo on all of them! I'm sure these will go quickly!

Jennifer

Re: Ebony Hollow Form

#4

Re: Ebony Hollow Form

georgetroy

>Great looking work. Mark, you are really cranking the work out. I thought you had a full time job. GT

Re: Ebony Hollow Form

#5

Re: Ebony Hollow Form

Mark Kauder, Phenix City, AL

>I do, but I have an addiction to feed as well. You should know, you helped me start it years ago.

Thanks for all your comments, GT

Mark

Re: Ebony Hollow Form

#6

Re: Ebony Hollow Form

Mark Kauder, Phenix City, AL

>I use Nitro-Celulose Lacquer. Highest quality I can find. Right now that is Lawrence-McFadden Guitar Rubbing Lacquer.

Thanks

Mark

Re: Ebony Hollow Form

#7

Re: Ebony Hollow Form

Ed Kelle

>This one is my favorite Mark. I usualy don't see many dark pieces and this one really works well. Those bowls are great also. Good job!

Re: Ebony Hollow Form

#8

I like this one

TD

>They are all very nice Mark but this one is my favorite. Aren't you the same guy that I offered a lathe for 5 wood vessels about 3 years ago?

TD

Re: Ebony Hollow Form

#9

Re: I like this one

Mark Kauder, Phenix City, AL

>Yeah, But if I recall, it wasn't a VB-36 though.

Thanks, TD

Mark

Re: Ebony Hollow Form

#10

Re: Ebony Hollow Form

George Van in WI

>Gosh Mark, you just posted some wonderful work and this is my favorite. Your finish on this black ebony against the Bloodwood is fantastic. I put this photo on my desktop so I can enjoy it for a while.

Thanks for posting, George

Re: Ebony Hollow Form

#11

Re: Ebony Hollow Form-hollowing the inside with?

Jill

>Wondering: What do you use to hollow out these small forms? I have a hollow form I am working on but have reached a point that I don't know which tool to use to finish the bottom of the inside. I am very, very new at turning so I am not sure if I am using the right approach or tool. My form is 3 inches tall with a neck opening diameter of 3/4 inches. I have made it to apx. 1/2 inches down inside of the form so far without killing myself...........only a few catches and frayed nerves. :-)

Re: Ebony Hollow Form

#12

Re: Ebony Hollow Form-hollowing the inside with?

Mark Kauder, Phenix City, AL

>Because I do segmented turning, the inside is mostly hollow to begin with, so mostly I have to turn the inside to the thickness I want, and finish the surface of the inside. On this one, I use a small Sorby hollowing tool like "A" in the attached link.

One of the first thing you can do is use a drill to remove the wood from the middle of the bowl, down to the depth of the bottom, and then use one of these swan-necked tools to slowly open the inside from the top down.

Not sure if that is much help.

Mark


img

Re: Ebony Hollow Form

#14

Re: Ebony Hollow Form-hollowing the inside with?

Jill

>Holly Cow Mark I thought I was the only one up this late. LOL Thanks for your advice. I do have the hollow master (kinda like a.) and I am trying it but it seems to be too wide to get into the neck very well.I seem to catch it also, not sure at what angle to have it. I do need to get a chuck for my tail stock so I can drill my forms out first. I think I will have to drill it out and then make another attempt at using the hollow master. I can't wait to finish this one.

Re: Ebony Hollow Form

#15

Re: Ebony Hollow Form-hollowing the inside with? *LINK*

Phil Joines

>I prefer taper shank drills to using a chuck. They are too long to use on a mini with a standard bed. If you get one use vice grip pliers to keep it from spinning in the tailstock. 15/32" is the largest made for a #2MT.


15/32" drill

Re: Ebony Hollow Form

#16

Re: Ebony Hollow Form-hollowing the inside with?

Mark Kauder, Phenix City, AL

>Actually, I was up that late because I am on call for our IT department, and I was awakened by my pager because one of our servers was down and had to be restarted. While waiting for it to come back on line, I checked the boards.

I have a Sorby Hollowmaster and it is one of my favorite hollow form Finishing tools with the teardrop shaped cutter. It works adequately for hollowing mid-sized bowls if you use the straight 1/4" cutter, but I would never use it on any thing with an opening less then about 1.5". You really need one of the smaller swan necked hollowing tools.

Mark

Re: Ebony Hollow Form

#17

Re: Ebony Hollow Form-ah oh I see

Jill

>Another tool purchase comin' on!! Yes, I think I have picked either too small of a hollow form or too big of a tool. ;-). Guess being a newbie comes with A LOT of lessons. Out to do some shopping.