Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Urban Salvaged Hardwood Slabs, Milled In-House from Rare Trees. Shop Unique Walnut Stock.

Remote Switch for DVR?

Posts

Remote Switch for DVR?

#1

Remote Switch for DVR?

Dick Parr

>Does anyone know if there is a remote on and off switch for the DVR? After watching the John Jordan hollowing video today I would like to get into deep hollowing. I would think a remote on and off switch would be ideal for this type of turning as he shows on his Woodfast lathe set up.

Thanks for any leads or information on a switch.

Dick

Re: Remote Switch for DVR?

#2

Re: Remote Switch for DVR?

Barry Irby

>Go on the Technatool site and rummage around. Maybe it was in the support group. Someone had posted a picture and explanation of how they did it. I'm not sure, it may have just been a kill switch, but I think they had fixed it so they could stop and start.

Re: Remote Switch for DVR?

#3

Re: Remote Switch for DVR? *LINK*

Larry E in NE OK

>Go to the Nova Owner's Group and post your question. It has a large number of members, someone is bound to have a solution.

Good Luck,

Larry


http://groups.msn.com/NovaOwners

Re: Remote Switch for DVR?

#4

Re: Remote Switch for DVR? *LINK*

Walter Ahlgrim

>This is photo of my second generation DVR remote. You can find my wiring diagram with this link or at nova owners group under photos �Walt Ahlgrim�s Album on page 2.

The flowing I posted here and in more woodturning.

DVR remote controls

Even before I bought my Nova DVR, the small and non-descript stop button seemed to me to be a weak spot on a machine with great features for its price. So I thought, no problem, I�ll just wire up safety switches to the 120 VAC input. Only after I got it home did I notice that when running, if you switch off the power, the lathe continues to run for several seconds.

Call me chicken, but I want to be out of the line fire when I push the start button. I decided to try adding extra switches to the lathe. I got out my ohm meter found the key pad is wired as shown in this fig 1 right side. I decided to keep it simple and have 2 remote functions: start and stop.

I made a small circuit board that plugs in-between the key pad and the interface board. This way, no permanent changes have been made to the lathe. From this board, 4 new wires run to the new buttons. See fig 1, left side. This has worked well for me, for over a year now.

For switches, I used arcade video game buttons. They are large, colorful, cheap, and indestructible. Mount them on a vertical surface so they do not fill with chips. I installed red stop buttons on both ends of my lathe. I turned a guard for the start button from an old pill bottle.

Now for the downsides:

1. If the start button were to become stuck, the lathe will start. When you press stop, it will only stop for a second then restart. In short, the lathe could start unexpectedly!

2. If the stop button were to become stuck, the lathe�s display will freeze at whatever is on the display and will not change until the button is released. If the stop switch is stuck, at power up the lathe will appear dead. It is very disconcerting to think the electronics in your lathe could have shot craps even for a few moments.

3. Certainly this would void your 1 year electronics warranty.

4. I have no way to know how well this circuit is isolated from the high voltage circuit. The voltages are low while the lathe is operating normally, however should something fail, how high a voltage you could be exposed to is anybody�s guess.

While I find this modification very convenient, it be could a dangerous thing to do to your lathe. So weigh the risks and the benefits for yourself. Feel free to email me if you need help with the schematics or parts.

Walter Ahlgrim


img

http://groups.msn.com/NovaOwners/dvrremotecontrols.msnw?Page=2

Re: Remote Switch for DVR?

#5

Re: Remote Switch for DVR?

Dick Parr

>Thank you all for the replies.

Dick

Re: Remote Switch for DVR?

#6

Re: Remote Switch for DVR?

Ralph Lindberg

>Dick, etal... I was going through the writeup on the new DVR-XP version of the Nova and noted a reference to a FACTORY remote, but could find no other information. SO....