Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

VPS-Level Performance. Fully Managed. No Hassle.

Tall and Skinny Burl Vase

Posts

Tall and Skinny Burl Vase

#1

Tall and Skinny Burl Vase

Bill Grumbine (Kutztown PA)

>Greetings all

Over the past week I have been a turnin' fool, spending lots of time on the lathe in preparation for a show. Here is one of the show pieces, which I am happy to say I do not own anymore.


This was a tough one for me on a couple of different levels. It was bone dry, and so it cut hard with the tool wanting to vibrate the whole time. It is also very skinny, at least for me. Overall size is 11 1/4" high, and 6 1/4" wide at the top. The bottom is about 2" in diameter. It is so narrow that SWMBO had to do the final sanding of the finish for me on the inside bottom since my hand would not fit in. Wall thickness is about 3/16". It is finished with Bush Oil, which I was encouraged to buy by the likes of Keith Tompkins and several others up at the Albany symposium. It is quite a bit thicker than the Watco I am used to using, and it seems to dry faster with less odor. I think I am really going to like using it, and may have to see about using up my supply of Watco on something else. As things go, I bought a brand new can of Watco just before leaving for the symposium, since I was very low. Oh well...

Buffed on a Beall wheel, with lots of trepidation.

Thanks for taking a look.

Bill

Re: Tall and Skinny Burl Vase

#2

Re: Tall and Skinny Burl Vase

Kevin Gerstenecker

>WOW, that is simply stunning Bill! Just when I think you cannot possibly out do yourself in the world of turning, you prove me wrong once again. ;-)

Beautiful flowing lines, and a spectacular piece of wood. I am not familiar with Bush Oil, I may have to look into trying that for a finish. Although I too am a fan of Watco, I am always looking for something different to try. Where may one find Bush Oil? I checked under all the bushes at my house, and all I found was soil! :-)

Thanks for sharing another beautiful turning Bill........simply beautiful work.

Re: Tall and Skinny Burl Vase

#3

Bill, did you find that...

Ted Owen, Pittsburgh

>the Bush Oil buffed out similar to the Watco? How many coats, and how long after final coat before you buffed?

Thanks.

Best, Ted

P.S. Been blowing up stuff left and right. But it's probably because I've been using wood with cracks--with practice in mind.

Re: Tall and Skinny Burl Vase

#4

Brad Vietje

Beauty, Bill !

Brad Vietje

>

Re: Tall and Skinny Burl Vase

#5

Re: Tall and Skinny Burl Vase

John Lucas

>GReat piece Bill. Glad it sold quickly.

Re: Tall and Skinny Burl Vase

#6

Re: Tall and Skinny Burl Vase

Donna Banfield

>Kevin

You might find Bush Oil at Woodcraft; the 2 stores I frequent in New England have carried it for about a year or so, now. In fact, I was in the Newington, NH Woodcraft when the rep from Bush Oil was demonstrating it for the owner. I listened to his pitch, looked at the samples he had on the different species of wood, and bought a quart that day. When that was gone I bought a gallon.

I prefer that to Watco, because I've found it easier to apply, and it doesn't have the 'gymnasium floor' glossy look to it. Not that there's anything wrong with that, ;-).

Re: Tall and Skinny Burl Vase

#7

Re: Tall and Skinny Burl Vase

Kurt Aebi

>Bill,

Another masterpiece, my man!

Glad it came out well and also glad that it is already sold!

Beautiful, Beautiful!

Re: Tall and Skinny Burl Vase

#8

Re: Tall and Skinny Burl Vase

Bill Grumbine (Kutztown PA)

>Thanks everyone!

Kevin, I am not exactly sure how to acquire a can of Bush Oil. I bought mine at the symposium in Albany, and the manufacturer is local to them. I will be researching it though, as I am pretty sure it is going to replace Watco for most if not all of my turnings.

Ted, the Bush Oil went on thicker, and gave better saturation with one coat (which is what the manufacturer recommends) than Watco does. The odor is also a lot less "intrusive" and seems to dissipate a whole lot faster. I was able to buff it the next day, but it has been fairly dry around here, so that may affect the speed of drying. Duck (sic) tape will help you hold those pieces together you know. ;-)

To add to Donna's response about Bush Oil, I have not seen it in the local Woodcraft stores, and now that the company has gone to more franchises, there are things that are not national. The stuff is not cheap, at $18.00/qt, but I got a gallon at $46.00 or something close to that. Perhaps Keith will have some more info on the guy and how to get the stuff.

Bill

Re: Tall and Skinny Burl Vase

#9

Re: Tall and Skinny Burl Vase *LINK*

Ed Kelle

>Bill

Lakeshore hardwoods is the only one I know who sells it. They shared a booth at a few shows I went to. Great work on the vase!


Bush oil

Re: Tall and Skinny Burl Vase

#10

Very, Very Nice Bill

Mark Kauder, Phenix City, AL

>

Re: Tall and Skinny Burl Vase

#11

Nice Bill!

TDaniel

>

Re: Tall and Skinny Burl Vase

#12

SWEET piece, Bill.

RevDoug

>

Re: Tall and Skinny Burl Vase

#13

You da Man

Gerry in Maryland

>Bill,

I'm always impressed by the turnings that you post. Now you go and get your wife to do your sanding! You da Man Bill..LOL

Gerry

Re: Tall and Skinny Burl Vase

#14

Re: Tall and Skinny Burl Vase

George Van in WI

>Fantastic looking piece Bill! You sure know how to show off the figure in this.

Thanks for posting, George

Re: Tall and Skinny Burl Vase

#15

Keith Tompkins

Re: Tall and Skinny Burl Vase

Keith Tompkins

>HI Bill, Very nicely done! Does the burl really stand out on this piece, or is that just the Bush Oil? LOL:).

I've known Bill Bush for several years. He is a cabinet and furniture maker supreme! His work has won numerous awards, has appeared in many publications incluing Architectural Digest and is featured in the "Source Book". HIs daughter is following in his footsteps, and is a great woodworker in her own right.He is a member of the Northeastern Woodworkers Association, as am I.

His oil finish is a proprietary blend, and is, in my opinion, far superior to other oil finishes. I field tested many oil and oil/poly finishes for Lily back in the seventies, and have used several finishes since, including my own mixes...so I feel fairly competent to give an opinion. I like the Bush Oil, and have even replaced many of my lacquer finishes with it.