Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Fast and affordable laser cutting – so you can make the parts you can’t find anywhere else

Grinder Problem

Posts

Grinder Problem

#1

Grinder Problem

Charlie Anderson

>I just noticed some has posted about the type of problem.

A while back, I was attempting to sharpen a cheap, small roughing gouge.

I have a woodcraft chinese grinder, 1825 rpm, I think. I also have a wolverine system.

I didn't have everything set up properly and when I touched the gouge to the wheel, it caught and was slammed do on the wolverine. (No fingers pinched luckily.) I did cause 'tearout' on the wheel. I've since dressed the tearout smooth, but there's still a problem.

I can't get the wheel true.

I've made sure to put downward pressure on the dresser so it can't move around as it does it's job. When I go to sharpen a tool, it bounces and the wheel ends up looking like the picture.

It seems I may have bent the shaft as there is a bit of left to right wobble in the wheel.

At the moment I can't get the other wheel off the grinder. When I do, I'll switch them and see what happens.


img

Re: Grinder Problem

#2

Charlie, look down the thread to "Bart"

TDaniel

>same problem as Bart is having. Reset your jig so the tool is higher on the wheel.

Re: Grinder Problem

#3

I understand that but

Charlie Anderson

>my problem is the problem with the grinder.

Another question: Is the thread on the left hand wheel not a 'righty tighty - lefty loosy' thread? I'm having a problem getting it off.

Re: Grinder Problem

#4

Pull both wheels off

Dustmaker Mike

>if you can. Then check for runout on the arbor of both sides. There shouldnot be an sloop on the arbor if there is a newbearing is needed if you are lucky if not then a new grinder. Just a guess it is a left handed thred on the wheel but I would not bet on it.

Re: Grinder Problem

#5

Re: I understand that but

Frank G ( Ingleside Texas )

>The nuts should thread on the opposite direction of the wheel. Standind in front of the grinder the left wheel should have left threads and the right whell should hibe right threads.

You could try loosening your wheels and turning them 1/4 turn at a time then re-tightening to find the best balance.

Re: Grinder Problem

#6

Threads

TDaniel

>Some of the cheaper grinders do not have left-hand threads on the left wheel. Also, the cheaper grinders have very thin plates to hold the wheels on and these are very easily bent. After getting the wheels off run the grinder to see if it is smooth without the wheels. Then put the wheels back on, one at a time, and run the grinder to see which one is bent. The One-way balancing kit includes a pair of good wheel mounting plates that should fix the problem if the shaft is not bent. Unfortunately, by the time you buy the new wheels and the balancing kit you will have spent the price of a cheap grinder. The Delta 1800 rpm grinder (which is rumoured to be discontined shortly) is the best grinder for the money that you can buy.

TD

Re: Grinder Problem

#7

similar problem

Dennis Taylor

>I had a similar problem, got a catch on the wheel (not paying attention) and after that my wheel didn't run true, mine was on the left side of the grinder....someone recommended replacement of the plastic sleeves first, I went to a machine shop and for 10.00, they made me bushings to fit my shaft & wheel center, and 4 plates to go over the inside & outside of the wheels on the left & right side, they have hubs that fit into the wheel opening, and since then they run perfect!....it was cheaper than the Oneway item I seen recommended, that was what I was going to get but someone pointed me to a machine shop...Dennis

Re: Grinder Problem

#8

re: similar problem

Dennis J. Gooding

>Or just turn your own bushings out of a piece of hardwood for nothing! DJG

Re: Grinder Problem

#9

My Conclusion

Charlie Anderson

>It appears to me that I have bent the shaft on the right side of the grinder. When I spin the wheel on that side it has a side to side wobble of about 1/32". When I move the wheel to the left side, there is no wobble.

I think I'll just live with the problem for now. I use the 120 grit wheel much more often than the 60 so I'll install it on the left.

Does this seem logical to you?

Re: Grinder Problem

#10

No!!

Mark Mandell - Gone Round In Jersey

>Trash the wheel, Charlie, it's not safe to use for powered grinding; especially the "friable" white and pink wheels. Even though you may dress it round again, it's most likely to have stress fractures which you won't see or feel until the wheel fractures under load. The risk of severe injury or DEATH is simply not worth the risk.

Re: Grinder Problem

#11

Charlie, try this.....

TDaniel

>Remove both wheels. Run the lathe. Does the shaft wobble? Does the grinder vibrate? Now put one wheel back on and try it again. If no vibration or wobble try the other wheel (unless the other wheel has a potential crack). As Mark said, if there is any potential that the wheel has a crack, even a slight potential, throw it away. If you have to throw one wheel away you can move the other one over to see if the grinder runs smooth with the other stone. Most of the time the wobble does not come from the shaft but the small plates that hold the wheel on the shaft or the bushings in the wheel. I strongly suspect that these thin plates have bent. If you have one side that wobbles just try the parts from the other side and see if you can make the wobble swap sides.

Re: Grinder Problem

#12

Re: My Conclusion

JKJ in East TN

>>It appears to me that I have bent the shaft

>on the right side of the grinder.

You can verify that with a dial indicator (remove the wheel and rotate the shaft by hand) or a long stick (rest the stick on the shaft a short distance from the end of the stick and hold that end to make a pivot - rotate the wheel and the end of the stick will magnify even very small runout.)

I didn't see where you suspected the wheel was cracked, but you can test by "pinging" it - hang the wheel by a cord or loosely on a rod through the hole and tap it with something like a wooden hammer handle. It should make a dead sound if cracked and a clear ping if sound. Compare to the other wheel. All new wheels should be tested this way before spinning them up. BTW, other good advice for just-installed grinding wheels (and cutoff wheels, etc) is to stand back and run the grinder at the highest speed for one minuute and see if it explodes.

If the shaft was bent from the catch, you might be able to straighten it with a wooden mallet and a dial indicator and a lot of patience. Some machine shops will straighten things like axles and shafts. I would not want the least amount of runnout in my grinder shaft. Better to replace it, although I suspect it would be cheaper to buy a new grinder.

JKJ

Re: Grinder Problem

#13

Thanks everybody

Charlie Anderson

>The gent who built and sold me the turnkey grinding system will be taking a look at it. (Unfortunately, not for 2 weeks.)

I suspect he will resolve the problem or tell me to buy a new grinder.

And I have confidence in him. He builds and sell lots of turning tools, including a hollowing system with all the bars.