Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Portable Sawmill & Tree Service – Abingdon, VA

tool rack

Posts

tool rack

#1

tool rack

John Lucas

>I spent the morning building tool racks to get those darn things out of the toolboxes. I built the first one around my craftsman tool box. It holds 60 tools and has room for a few more. One can never have enough tools. Most of these are homemade by the way. Parting tools on the left, skews on the right from 1" down to 3/32. Scraping tools behind those. Gouges on the back line with small hollowing tools and specialty tools behind those.


img

Re: tool rack

#2

Re: tool rack

John Lucas

>Here is my wall rack. These tools wouldn't fit in a hole very easy. I also plan to put my boring bar with the other extension bars on this wall as well as my really big gouges.


img

Re: tool rack

#3

Re: tool rack

DWFII

>I like the idea of the wall rack but I have a question...or rather an experience that leads to a question I tried to build a rack based on a similar principle using single rare earth magnets for the tools. But after mounting one bowl gouge in the rack for about 15 minutes it became so magnetized it now sticks to the tool rest--not like the rare earth magnet itself would stick but enough to make sliding the tool on the rest a little harder. I don't like that.

How did you get around magnetizing your tools?

DW

In the High Desert of Central Oregon

Re: tool rack

#4

Re: tool rack

George Van in WI

>Thanks for the tips John, I am just trying to organize a little, and your photos give me something to start with!

Re: tool rack

#5

Re: tool rack

The Wood Spinner / Bill Hale

>DW

The magnetic effect is of no concern as you want the tool in contact with the rest anyway.

I have had mine set up similar to this for several years and all of the tools are magnetic. My other tools in my roll around are not and I do not even notice the difference whem working.

Good turning and be safe

Bill in Casa Grande, AZ.

Re: tool rack

#6

Re: tool rack

JKJ in East TN

>>How did you get around magnetizing your tools?

DWFII,

I ran into that as well. I magnatized one 1/2 skew and it drove me nuts until I demagnatized it. For me, the magnetism interfered with my technique.

I personally like my lathe tools presented a little differently than most. I lay them on some shelves behind and to the side of the lathe, but I put them with handles to the back and the sharp edges towards me. At first, I worried that I might draw blood one day reaching for a tool, but this proved not to be the case.

With the tip towards me, I always grab the right one. With the handle showing and the tip hidden, I'd have to mark each handle then remember the marks, or mark the spots and be sure to put each back in the correct spot each time - ain't gonna happen.

One unexpected benefit - when reaching for a certain tool I sometimes notice a different one and decide to experiment. This led me to discover the other day that a sharp spear point scraper is a very efficient tool for rounding extremely rough out-of-balance chain-sawn bowl blanks. Beats the heck out of taking a beating with a gouge.

Just curious, for those who put the tips down into some type of holder where they are hidden - how do you distinguish them by looking at the handles?

JKJ

Re: tool rack

#7

Re: tool rack

John Lucas

>John That's why my tools are in a certain order and also many have different handles. That makes it easy to grap the right one.

Re: tool rack

#8

Re: tool rack

John Lucas

>I've used magnets to hold tools for years and really never noticed a problem. On really rare occasions I will notice it. I have a magnetizer/demagnetizer so I just demagentize them.

Re: tool rack

#9

Re: tool rack

Rick in Colgate, Wi

>I've been using those broom holders that are plastic coated and attach them to a board thats mounted on the wall to the right of my lathe within arms reach. They are bendable and you can make them fit just about any size handle.

Re: tool rack

#10

Re: tool rack

JKJ in East TN

>>and also many have different handles.

Ah ha, you must be one of those young guys I've heard of who still has a good memory!

I've read of people painting or othewise encoding the handles, but that still would require somehow remembering which handle was the 3/8 bowl gouge with the steep angle. I'd probably have to paint little tip diagrams on the handles. Maybe a diagram or label on each slot?

JKJ

Re: tool rack

#11

How can you get

Phil Joines

>any work done with so few tools? :>) :>) :>) :>) :>) :>) :>) :>) :>) :>) :>) :>)

Re: tool rack

#12

Re: How can you get

John Lucas

>Rule no 1. Never turn anything unless it requires a new tool.

Re: tool rack

#13

Re: tool rack

John Lucas

>Don Russel in Atlanta teaches classes and has all of his tools painted for a certain type. He chose red for the skew which he thought appropriate.