Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

Pin Chucks, Fuctionality?

Posts

Pin Chucks, Fuctionality?

#1

Pin Chucks, Fuctionality?

Jim Shaver - Oakville, Ontario

>Hi,

I am curious how a pin chuck works. I was visiting a pen turner this past week in Arizona, he uses a pin chuck to hold a pen blank so he can turn the end of the pen with no hardware. The chuck appeared to be a bar of appropriate diameter to match the pen tube, but with a flat ground into one side of the bar stock.

The bar is captured in a small set of jaws on the head stock, but there is also a small roller bar that is inserted into the the tube and appears to sit on this ground flat section.

Apparently this combination of the small roller bar and the ground flat secon act together to capture the pen and hold it steadfast while turning...question is, I do not undertsand how this works.

Can some one explain the principle to me?

Thanks...

take care,

Jim

Re: Pin Chucks, Fuctionality?

#2

Re: Pin Chucks, Fuctionality?

Eaglesc

>I am no expert, but as the mandrel tries to roll in the tube,the "pin" slides in the recess and jams against the tube.

Picture using a round piece of wood "chocking" a tire to preventit from rolling.

I draw the live center up to the end of the blank and only pull it back for finishing.

Re: Pin Chucks, Fuctionality?

#3

Re: Pin Chucks, Fuctionality?

Barry Irby

>Eaglesc described exactly how it works. The roller pins jambs or wedges itself. I don't have a lot of experience with them but last fall our Turing club agreed to make tops for a local 4-H group. I ended up making eighteen. Had trouble getting the prepared blocks to run true and made a little pin chuck just as you describe. The hole was 5/16", I ground a flat on one side of a steel rod and used a nail for a pin. Worked great. Seems to tighten the stock against the rod and keep it really straight in the hole. To remove it you just rotate the work slightly in the opposite direction and slide it off. Very quick and easy.

They make larger ones that have about a 1" bar (Maybe 1 1/4"?)with a set of female threads in the other end that screw onto the shaft or you lathe. You drill a corresponding hole in your bowl blank. slip it on and turn the outside. I would use the tail stock.

I would think it would be important that the piece of wood you are turning be large enough in diameter to resist the tendency of the pin to bulge the side. If the hole were not "sturdy" enough, it would not work. Same thing for really soft, green or punky wood.

Re: Pin Chucks, Fuctionality?

#4

Re: Pin Chucks, Fuctionality?

Wally Dickerman in Arizona

>A pin chuck works very well when turning a natural edge bowl or vessel. Just drill the appropriate size hole, insert the blank, any size, on the pin chuck and turn the outside of the piece including the foot. To remove the piece, just roll it a little and pull or knock it off. My pin chuck is 1 1/8-inch in dia. It's a good idea to use the tailstock for large pieces.

Wally

Re: Pin Chucks, Fuctionality?

#5

Re: Pin Chucks, Fuctionality?

Jennifer@Indy.USA

>Jim,

I'm almost certain that Best Woods was selling them at their booth at the AAW Symposium in Kansas...but I don't see them on their website? Max Krimmel uses the pin chuck for turning alabaster pieces and so we got a good look at how they work. It's really a fantastic idea. Apparently easy to make as well, from what I gather. Just grind a flat on a piece of drill rod to hold the pin? You'd have to figure a secure way to hold the rod though.

Jen

Re: Pin Chucks, Fuctionality?

#6

Thank You Everyone

Jim Shaver - Oakville, Ontario

>I appreciate all of your input.

I have a much better understanding of how they work now, Thank You!

I'll be looking into a few for my pen notions in the coming months, should be fun!!

take care,

Jim

Re: Pin Chucks, Fuctionality?

#7

Re: Pin Chucks, Fuctionality?

Ken Grunke from SW WI

>My other hobby is metalworking, and I machined a set of pin chucks in nominal sizes from 3/8" to 1" held in a setscrew collar that screws onto my lathe. Very useful for vases which use glass tube inserts, but with soft woods or thin sections you can have problems.