Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

THE WOODRAT IS BACK!

power carving advice please

Posts

power carving advice please

#1

power carving advice please

ken chase

>Couldn't find anything in articles and revues. I have an interest in purchasing power carving and grinding tools to enhanse my turnings and don't have a clue which products are the best choice. Imput will be greatly appreciated.

Thanks

Re: power carving advice please

#2

JL

Re: power carving - try Woodcarving board

JL

>

Re: power carving advice please

#3

Re: Power carving advise *LINK*

Michael Serpa

>A good start would be: Treeline


http://www.treeline.com

Re: power carving advice please

#4

Re: power carving advice please

John Lucas

>Ken I do an awful lot of rotary power carving with a dremel and an old flex shaft machine. The dremel works good for fine detail and the flex shaft machine I use for hogging off wood. You could probably do both with a good flex shaft machine such as one of the Foredom models.

I buy most of my bits from either Woodcraft or www.riogrande.com. Rio Grand is a jewelry supplier and they have a lot of small bits at really good prices.

Re: power carving advice please

#5

Re: power carving advice please

stacey s

>Ken,

Last week I purchased a foredom flex shaft carver from my local Lowes store. It was on clearance for about half price normally 230 got it for 130. I really like it. THey also had all of their foredom brand cutters on clearance at half price. Stacey

Re: power carving advice please

#6

Re: Thanks for the posts

ken chase

>

Re: power carving advice please

#7

Re: Thanks for the posts

Sascha

>I started enhancing my turnings as well and here is my selection of tools I have bought so far.

-Powercrafter carving system

-Proxxon reciprocating carver

-Proxxon minigrinder with 2 different Kutzall wheels as well as the 2" arbortech wheel.

-4" arbortech wheel in regular grinder

-various ball mills/bits in airpowered die grinders

-Detailmaster burning tool with 2 outlets.

So far I have liked every single tool I got, but I realy like those little Kutzall wheels, they remove wood very fast and the Proxxon grinder lets me controll the cut very good since it is so lightweight.

Treeline really is a good place to start, as is Craft supplies.

Sascha

Re: power carving advice please

#8

Re: Thanks for the posts

ken chase

>great info. Thanks. I spoke to a tech at Treeline and his advice was to get a Foredom and add a Wecheer carver to use with it. Would this combo be at all comparable to your set-up?

Re: power carving advice please

#9

Re: power carving advice please

Darryl Hansen

>Ken I just located a Wecheer 1/3hp flex shaft with 20 bits. As I remember it was about 159 shipped to Maryland. The Mastercarver for 99 was the next best. It was 1/4 hp no bits and shipping extra from Carver Supplies. I tried the Woodcarving Board and only received one reply form one of the contributors from the message Baord John Lucas. If you want to pursue the Wecheer let me know and I'll find the link for you...Darryl

Re: power carving advice please

#10

Re: power carving advice please

ken chase

>Darryl: I would appreciate the link. I am totally confused. I have not done power carving so I'm not familiar with any of the tools available. I tend to be obsessive about researching tools before buying and imput from this board is very helpful.Thanks much

Ken

Re: power carving advice please

#11

Re: power carving advice please

Darryl Hansen

>Me too. www.traditionalwoodworker.com 1-800-509-0081 Item 242-3301 I note they are now on back order but call them and see. Mine should be here tomorrow and I'll let you know how it works and feels...Darryl

Re: power carving advice please

#12

Re: power carving advice please

ken chase

>Thanks. Didn't know Wecheer made a total package. Is it as powerful as using the Foredom as the power source?

Re: power carving advice please

#13

Re: power carving advice please

Darryl

>Ken I received the Wecheer 1/3 hp today. Well built, works as advertized. Now I need to learn how to use it...Darryl