Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Personalized Wooden Watches, Engraved Free

Collet Chuck - New Purchase *LINK*

Posts

Collet Chuck - New Purchase *LINK*

#1

Collet Chuck - New Purchase *LINK*

Gary Ratajczak

>I was in my local Woodcraft store last week, and spotted this chuck set. It's similar to the competition, but an imported version. $79.00 includes a MT2 chuck, along with the FULL set of collets. Great for bottle stopper and mine turing. I'll be using on a Jet mini. First inspection - quality is very good. After you get the oil wiped off, seems like a solid setup. Collets are all machined very well. I'll post an update when i give it a try.


Woodcraft collet chuck

Re: Collet Chuck - New Purchase *LINK*

#2

Re: Collet Chuck - is the MT threaded?

Bud

>This looks great however, is the MT threaded in the back for a draw bar? Otherwise you have same problem with most Jacobs chucks -fine if you support the opposite end with the tailstock, but could get �exciting� or at the very least a PITA with the MT constantly coming lose as your cutting,unless the work piece is supported by the tailstock. As a safety note kinda on the same subject- a well known demonstrator was in front of a large audience and was boring a long hole in a large hollow form with a very long bit mounted in a Jacobs chuck, as he was pulling the tail stock back, to back out the bit, the Jacobs chuck came out of the tailstock with the MT flailing around at 800 rpm, what made the situation even more thrilling, was the stop switch was at the headstock and the demonstrator was at the tailstock while he was drilling.

Would like a reasonably priced collet chuck that screws right on the spindle.

Turn safe, Bud in IL

Re: Collet Chuck - New Purchase *LINK*

#3

Re: Collet Chuck - is the MT threaded?

Eduardo Sarmiento Hall,lima peru

>BEAL COMPANY MAKES WHAT YOU NEED AND AT THE SAME PRICE

MY 2CENTS

Re: Collet Chuck - New Purchase *LINK*

#4

Re: Can someone please explain this to me?

Al Crandall- NE of Indy

>I spent 36+ years in a toolroom, and I don't remember even one instance where where I had a Morse taper tailstock to loose its grip on the tang of a drill or a chuck. But it seems to be a common occurance with wood lathes. Why is this? I've also drilled holes 36" deep with radial arm drill presses, and believe me, you do a lot of backing out when going that deep. The chucks never fell out of the quills in those machines either.

Re: Collet Chuck - New Purchase *LINK*

#5

Re: Can someone please explain this to me?

Bill Howatt

>I think it may be because the morse tapers don't get really jammed into the headstock by "drilling" pressures like they do in a metal-working operation. I don't know if the lateral forces caused by cutting (as in spindle turning) cause the morse taper to work free. Without a draw bar or tailstock they certainly come loose.

Bill

Re: Collet Chuck - New Purchase *LINK*

#6

Re: Can someone please explain this to me?

Gary Ratajczak

>Yes - MT is threaded on the back to accept a draw bar. As far as the other chucks on the market, price does not include collets. So.... you would be at $200.00 for a comparable set. I think the quality is good on this one. I always opt for a made in america, but for casual use this pakage seems like it falls at the right price point.

Re: Collet Chuck - New Purchase *LINK*

#7

Re: Can someone please explain this to me?

JKJ in East TN

>I thought it was because the tapers in most machinery are put into place and stay there, while woodworkers constantly remove and insert the tapers. Perhaps this allows foreign material to enter and prevent a good grip (plenty of dust around wood lathes).

JKJ

Re: Collet Chuck - New Purchase *LINK*

#8

Re: Can someone please explain this to me?

RussFairfield

>I have always wondered the same thing as Al. After all, the Morse Taper was patented as, and is known in the machine tool industry as a SELF-LOCKING taper. And those words mean exactly what they say.

The MT is an interference fit between 2 smooth surfaces, and it does take a sharp blow to make them "lock" together. If they are a perfect match, this blow can be from the tang itself as we pop the tool into place. Sometimes it takes a rap with a dead-blow hammer. Could this little rap with the weight of the tool or a hammer be the difference? I think there are a lot of folks who need a short instruction in the use of Morse Tapers. I served an apprenticeship as a machinist, and one of the first things I learned about was Morse Tapers and how to use them. They are an important part of the trade. I have yet to see the 1st woodturning demonstrator mention the 1st word about MT's, what they are, and how to use them; other than how to add a draw bolt.

The obvious difference is that those tapers in the machine shop were matched and ground surfaces, and those we find in most lathes and on the tangs of most woodturning tools are not. Most of our lathe spindles are reamed, and most of the MTs I see on tools are a pretty rough tool surface. I can see where some of these might be difficult to separate once they got locked together.

The taper in my Oneway is a ground surface and an accurate taper. A matching taper stays put with a light tap from the lead hammer, and breaks with a similar quick rap with the bar on the back side. Some of the tapers aren't a perfect match, and they take a harder blow, and some of them take a little cleaning-up with a file and emery cloth; but I have yet to find one that didn't "self-lock". Never having to use a draw-bar may be one of those hidden things we get for the extra $3k we pay for the high priced lathe.

Re: Collet Chuck - New Purchase *LINK*

#9

I agree Russ....

TDaniel

>it is the poor machining of the 2 surfaces that is causing the problems. Another example of "you get what you pay for" (sometimes).

Re: Collet Chuck - New Purchase *LINK*

#10

Re: Collet Chuck - is the MT threaded?

tek-Brunswick, Ohio

>Yes it is threaded for a drawbar. I've been very happy with mive>

Tom

Re: Collet Chuck - New Purchase *LINK*

#11

Method?

Bill Howatt

>I wonder how many people seat them with a lead hammer or anything else for that matter other than push them in quickly by hand?

I know I don't "hit" them.

Bill

Re: Collet Chuck - New Purchase *LINK*

#12

Re: Can someone please explain this to me?

Juergen

>Probably because all of the dust that collects in the spindle and the tailstock ram. Since I've religiously started cleaning the female side of the taper I've not spun one. Don't see much shavings and wood dust in a tool room.

Re: Collet Chuck - New Purchase *LINK*

#13

Re: What I'd like to know....

Danny Wells

>is why they left the 7/16 collet out of the set? That's exactly the one I would need. That just makes no sense.

Russ...thanks for the instruction on the tap. I had never heard that, and always wondered why my Jacobs chuck wouldn't stay in the headstock. I'll definitely use that the next time. It's amazing the little things you'll learn around here.

Re: Collet Chuck - New Purchase *LINK*

#14

Re: Collet Chuck - New Purchase

Eaglesc

>"I was in my local Woodcraft store last week, and spotted this chuck set. It's similar to the competition, but an imported version. "

If the imorted version y9u are referring to is the Beall set be advised mine are Bealls and ther are stamped "made in China"

I am happy with them but don't think for one minute they are not made oversea.

I do enjoy not havin to use a draw bar.