Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Reach the woodworkers who ACTUALLY BUY

DC and the lathe question?

Posts

DC and the lathe question?

#1

DC and the lathe question?

Barry Irby

>I have a small shop and the lathe makes a big mess. I turn bowls and the stuff sprays every where. I mentioned down below that I have DC on my other tools but gave up when I got to the lathe. I have a 6" port waiting. Is anyone doing anything that works well?

I thought about putting up some sort of curtain like around a hospital bed/ shower curtain to try to confine the spray to a minimum. Seems like something that hung down to about waist height would do a lot to confine the chips. Maybe some of those plastic strips like they have on the doors at Lowes. I find chips ten or more feet away.

Re: DC and the lathe question?

#2

just 10 ft?

TDaniel

>Barry, a shower curtain will work to some extent but then it also confines any dust to the area where your breathable air comes from. Try to balance the blocking of the spray with good air flow.

TD

Re: DC and the lathe question?

#3

Re: just 10 ft?

Don Tewell

>A good friend and teacher just uses plastic curtains that just suround the area he wants to be kept fairly clean. Like over his sharpening table. He has a large DC but found it's more trouble than it's worth. Just buy a good broom.

Re: DC and the lathe question?

#4

Re: DC and the lathe question?

John Lucas

>Barry I'm going through the same problem in my new shop. I am going to install some roll up bamboo, or whatever that material is, curtains. My shop gets awfully hot in the summer and I need as much air as possible to get through. You can get those curtains quite wide. I still use a dust collector, it helps cut down on the small floating dust.

Re: DC and the lathe question?

#5

Re: DC and the lathe question?

Bill Howatt

>Since you are tight on room then the curtain idea is probably a good one for you. When I realized what the lathe was doing to the rest of my shop I redesigned my finished basement plans and put in a small lathe room (8.5' x 6.5'). My experience was that a DC was useless for anything other than sanding and I use it for that. I shovel and sweep the shavings and I no longer try to get 100% of them because the last 10% took the most time and it is a wasted effort - they come back so quickly!

If I were to do it again I would make the room bigger.

Bill

Re: DC and the lathe question?

#6

Re: DC and the lathe question?

Fog Tanner

>Barry, I have a dust collection setup, which I described in your other post. It works for me in capturing most of the dust, its intended purpose, and some shavings. But the larger shavings are going to fly. It would take an extrenly large amount of airflow to capture the shavings, something like one of those large floor fans behind your lathe pointing away from you. And that wouldn't get everything.

I had thought about the curtin you described for the same reason, but living close to the Texas coast where we have three days of brutal winter where it drops into the 70's or sometimes worse into the 60's, I have a fan on most of the time (except those three days). This precludes a curtin "box" in our area. But, it doesn direct the shavings into a given direction - more or less. There are some turners in our club who use a curtin as a wall to stop the shavings, and this seems to work well in thier shops. One member uses the old roll down window shades, but I have heard of shower curtin or just a sheet of plastic.

The other problem with a "box" around your turning area is the concentration of dust that you would be feeding your lungs or respirator. Either of which will just get clogged up quicker. And when turning bowls, you are going to generate dust when cutting and scraping. You can see this if you have a contrasting back drop. I see it going into my black dust collector "funnel". So, its not just when sanding that you will be filling the air with fine particles.

One of the things I did when I ran the metal ducting fro my DC, was to add a floor sweep next to the lathe. I keep a broom by it and when the shavings get too deep, I sweep them into the floor sweep. The bin on my cyclone is a 55 gallon drum, which I mounted on a dolly so it is easy to unhook and roll around and empty. I found that I would keep the floor clean more often when I made it more convenient.

Fog