Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Abingdon, VA – Tree Cutting & Portable Sawmill

no ruffles but some ridges

Posts

no ruffles but some ridges

#1

no ruffles but some ridges

DWFII

>I'm still working on my crabapple vase. I've nearly got it done. I've been using the Sorby Hollowmaster and the Multitip tool. Both work really well...although I couldn't get my half inch Keltons to stop "chattering." Driven only twice, on consecutive Sundays, extremely low miles...any bids?

Now I don't know if it was the Keltons or something else I did...no matter...but as I'm scraping the inside of the vase I have some "ridges"--soft, kind of wide ridges--that I can feel with my finger under the somewhat pronounced shoulder of the vase. But I can't seem to get rid of them. I can't feel them with the tool and I can't mark them with a grease pencil. If I make a guess as to where to position my scraper tip, I end up making the "pipe" deeper or making a whole new pipe and hence a new ridge. [sigh]

Can someone give me some advise as to how to deal with this sort of problem even if it's beyond my present competancy?

DW

In the High Desert of Central Oregon

Re: no ruffles but some ridges

#2

Re: no ruffles but some ridges

John Lucas

>DW I slow the wood down and dampen the vibrations with my hand on the outside and take extremely light cuts on the inside. You might also try tilting the blade a little bit differently than your original cut. You may not be able to do this but changing the angle even slightly will help take off the high points of the chatter.

Re: no ruffles but some ridges

#3

Re: no ruffles but some ridges

DWFII

>Thanks John. It's sure a puzzle. The Dorby Hoolowmaster includes a short cutter (not the scraper) that actually has less surface contact with the wood than the Keltons. Yet, the minute I get even close to the wood the keltons start screeching. The Sorby, though it has to have a larger hole for entering, doesn't do that. I tried positioning the Keltons at center, above center, and even slightly below center and I tried tilting them a little and so forth. But I can't seem to get the hang of them...leastwise not on this dried crab apple.

But I still don't know how to eliminate these soft ridges...

DW

In the High Desert of Central Oregon

Re: no ruffles but some ridges

#4

Brad Vietje

Re: no ruffles but some ridges

Brad Vietje

>DW:

I usually use a wider, teardrop scraper, or a bullet-shaped scraper for the lightest touch of shear scraping inside hollow forms and vases to clean up ridges. I keep the tip well above center. I also hold the outside very lightly with my left hand to dampen vibrations, but that can be pretty scary until you are so used to your tools that a catch is very unlikely. The scraper tip should be freshly sharpened and/or honed for the best results. It seems that the wider, shallower ridges are harder to correct (feel/see/find) than the narrow ridges from the smaller tips.

Safe Spinning,

Brad Vietje

Thetford, VT

Re: no ruffles but some ridges

#5

Re: no ruffles but some ridges

DWFII

>Brad,

thanks...

The Sorby Hollowmaster (spelled it right that time!) includes a round scraper. I like it real well. It is only minimally larger than the shaft of the tool. The Sorby Multitip comes with a tear-drop shaped scraper that is great for outside but trying to get it into the neck of my vase would be silly--it's just too large.

What do you use for narrow mouthed vases? What tool and what scraper?

DW

In the High Desert of Central Oregon

Re: no ruffles but some ridges

#6

Brad Vietje

Re: no ruffles but some ridges

Brad Vietje

>DW,

I usually hollow with home-made Ellsworth-style boring bars with 3/16" cutters, a set of 1/2" boring bars (straight and bent neck) from John Jordan (same tips), and a set I bought from Michael Hosaluk. I have a Sorby Hooker tool & Armbrace with a big teardrop scraper, but only use it where the mouth is wider than about 1.25" For smaller vessels, I clean up with a Sorby goose-neck tool and a 3/8" bullet tip. I pretty commonly make thin hollow forms with 1/2" openings, and the 3/8" tool works pretty well with steady hands and a single cup of coffee (I use a big CLTL mug, so that's probably three cups !).

For real small ones and mini's (1/4" - 3/8" openings) I use home-made tools from allen wrenches and small rt-angled machining tips ground to form little round tip scrapers -- these I do not sand inside.

i'll attach a 6" diameter H.F. in Mesquite Burl from Unique Mesquite, with ~ 3/4" opening.

Safe Spinning,

Brad Vietje

Thetford, VT


img