Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

100+ Wood Species + Full-Shop Services: Lumber, Veneer, Tools & CNC. Everything in One Place.

Socket chisel handles

Posts

Socket chisel handles

#1

Socket chisel handles

John Stankus, Plano, TX

>I need some help trying to figure out the best way to match the taper for a socket chisel handle. My brother asked me to make some replacement handles for some used chisels he picked up and I can't seem to get the taper correct. Is there any trick? I did an archive search and didn't see anything.

Thanks

John

Re: Socket chisel handles

#2

Re: Socket chisel handles

John Lucas

>John Measure the top width of the taper and then measure down into the taper a known distance. I have a 3/4" and a 1/2" wide ruler. I stick them in the socket until they bottom out. Then I check the depth. Then all you have to do is cut these dimensions on your wood. For example if it's 3/4" wide and 1" down it's 1/2" wide, you simply transfer these dimensions to the handle and cut a taper that starts 3/4" wide and 1" away from that it tapers to 1/2" wide. Then you can make it as long as necessary using the same taper to get the full depth of the handle.

Re: Socket chisel handles

#3

Re: Socket chisel handles

tek-Brunswick, Ohio

>Turn the handles as close to the taper as you can, but leave the diameter a little oversized. Push the taper into the socket and twist the handle. The socket will burnish the high spots. Turn off the high spots and repeat, after a few tries the taper will be right on. If it�s still oversized, just take an even amount off the whole taper. You should have a shoulder between the top of the socket and the handle. Leave a little space, maybe 1/8� or 3/32� between the shoulder and the socket. After the chisel is used a short while it will seat all the way against he shoulder. Hickory makes good handles. It is hard and resilient. It doesn�t turn quickly though. You have to take your time with it.

Tom

Re: Socket chisel handles

#4

Re: Socket chisel handles

William Duffield, on the Cohansey

>Instead of a ruler, I use two wooden dowels, of different diameters, both smaller than the maximum diameter of the taper. Make sure they are not beveled on the end. Insert them into the socket, and mark the dowel itself with a pencil, and transfer this directly to the handle. Use a dividers right off the dowel while turning to depth with a parting tool. Then clean up the taper with a skew.

To do final fitting, instead of putting the handle back on the lathe, I just scrape off the burnished, high spots with a card scraper, and retry, until it fits. This is especially useful if it is an old hand forged tool, with a socket that is not round.

Re: Socket chisel handles

#5

Re: Socket chisel handles

Pete in Holland, MI

>Make sure the tip of the taper doesn't touch off on the bottom of the socket, else you'll never get it to seat.

Re: Socket chisel handles

#6

Re: Socket chisel handles

Al Kapocius

>Think it was Bill Grumbine who used this method. Find a drill that's a mite wider than the bottom of the socket (doesn't wiggle). Use the drill diameter to size the end of the taper and depth of the drill for the length. Top of the socket opening will give you the other diameter. Turn the taper between the two diameters.

If'n you really want to get fancy, cut and glue leather washers between the top of the socket and the handle. A stack of glued leather washers at the end of the handle are another consideration if it's subject to lottsa impact.

Al Kapocius

Re: Socket chisel handles

#7

Re: Socket chisel handles

Bruce in Saint John, N.B. Canada

>John I ran into this same problem a couple of years ago, and thought there must be some kind of simple way to duplicate the taper. What I did was use the chisel handle cavity as a mould. I lightly oiled (lube oil) the handle cavity and then mixed up the some epoxy and filled the cavity, I placed a # 10 wood screw (2" long) in the epoxy, left a portion of the screw proud, and left it overnight so it would sure to be cured. The next morning I pulled on the screw that was sticking up out of the epoxy and out came an exact duplicate of the taper. One could no doubt put wax or some other product in the cavity to keep the epoxy from sticking to the metal chisel but I just happened to have some oil close by when I was trying this. Like Pete says carefull the length of you new handle is not too long as you don't want it to bottom out. Thats how I did it John, think it was two winters ago and the handles haven't come out yet. Good Luck....

Bruce in Saint John, N.B. Canada