Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

Chainsaw Blade Question.

Posts

Chainsaw Blade Question.

#1

Chainsaw Blade Question.

Jim J.

>I recently acquired (a gift!) an 18" Sears chainsaw, along with a second 16" bar and chain. I have previously read, and cannot find the source again, that one needs to use a "rip" chain when cutting longitudinally down a tree trunk to remove the pith. Please could somebody let me know where I could buy the necessary chain. I would also like to take the opportunity to thank all those people who share their wisdom on the this board, making it a wonderful resource. My compliments to you all. Thank you. Jim J.

PS. I am located in Texas.

Re: Chainsaw Blade Question.

#2

Re: Chainsaw Blade Question.

Ryan McMullen

>I do not use a "rip" chain when removing the pith. I cut parrallel to the grain (this yields long strings of fiber).

If you cut the end grain, the I believe you will need the rip chain. I think it is also recommend that with a rip chain you have a special device to hold the chainsaw while sawing as the potential for kick back is greatly increased.

I could be wrong here, but I believe this is what I read somewhere.

Re: Chainsaw Blade Question.

#3

Re: Chainsaw Blade Question.

Curt Fuller

>Most chainsaw dealers will either carry or order in a 'rip' type chain. But if you have a spare chain or one that's getting about worn out, you can use a dremel sharpening kit and just change the angle of the cutting edge to a more square angle. There are some other differences in rip chains but that will make any chain cut more effectively with the grain. Unless you're really planning on milling a lot of logs, any good sharp chain will work for small jobs. Makes a lot of long peeled shavings that tend to clog up the saw though.

Re: Chainsaw Blade Question.

#4

Re: Chainsaw Blade Question.

Carole in VA

>You can cut down the trunk with a regular chain. It just takes a little longer. I prefer to put the long on it's side and cut length-wise, but you do have to clean the long shavings out often. From what I have been told, rip chains can be very dangerous. Do a search on here for chainsaws or rip chain and you will find wealth of discussions on the subject.

Re: Chainsaw Blade Question.

#5

Re: Chainsaw Blade Question. *LINK*

Ken Grunke from SW WI

>If you don't mind joining another forum, here's a good place to ask questions like yours:


Forestry Forum

Re: Chainsaw Blade Question.

#6

Hmmmm...

Ken Grunke from SW WI

>Didn't mean for that to sound like a brushoff or anything, just trying to be helpful :)

I've found the people there to be very knowledgable about chainsaws. If you talk to Charlie, tell him I sent you--he's in our AAW chapter.

Re: Chainsaw Blade Question.

#7

Dick Hines

Re: Chainsaw Blade Question.

Dick Hines

>Forget the rip chain. Just lay the log on it's side and cut away. Just make sure you have some of the teeth on the saw in the log.

Danger!!! The wood will come off in ribons. DO NOT clear the chip shoot with the saw running. Your new nick name may be stubby.

Re: Chainsaw Blade Question.

#8

Re: Chuckle . . . Thanks.

Jim J.

>No offense taken. I asked on this board, as I know that many wood turners prepare their own green blanks. I have not used the other board, and they no doubt have many knowledgeable chain saw users - but are they also wood turners know our application? Thank you for all of the comments, I will put them to good use. Jim J.

Re: Chainsaw Blade Question.

#9

depend on use

JKJ in East TN

>How much ripping do you plan?

I read an article last night about cutting lumber with a chain saw - all of this is ripping. The author stressed the importance of using a rip chain for efficiency.

The article indicates that too many teeth overload the engine and jam the saw. A skip chain, which has an extra link between each tooth, is strongly recommended for ripping. The rip chain alternates pairs of scoring and raking cutters. The teeth are not ground the same as a standard chain. This was an old article and I don't have good recent information. In researching sawmills, I did find that today's mill manufacturers sell special rip chain and it is quite expensive.

Although way too slow for milling lumber, if you only occasionally rip an occasional log section, as I do to prepare turning blanks, the standard chain will work. I have to stop occasionally and clean out the shavings.

JKJ

Re: Chainsaw Blade Question.

#10

Jim, this is what I do.....

TDaniel

>For a few blanks just use the standard chain. Do not use a ripchain that was designed to be used in a frame. If you have a lot of blanks to saw and they are big then you will want a skip-tooth chain. The rip-chains are very difficult to sharpen and are not worth the effort and as others have said, they are dangerous to use if not held in a frame. For really big blanks a double skip tooth can be used.

TD

Re: Chainsaw Blade Question.

#11

Re: Chainsaw Blade Question.

Don Henthorn

>I always approach the log at an angle instead of cutting with the bar parallel to the log. Cutting with the bar parallel to the length will give long, stringy ribbons which can clog up your saw and slow the cutting. Cutting at an angle makes short ribbons which clog less and make the saw work less hard. That's my story and I'm stuck with it.(-:

Re: Chainsaw Blade Question.

#12

Re: Chainsaw Blade Question.

Tim Conlon

>You want info on ripping chain? read on! BTW - the main danger involved with any chain is if you get the tip of the bar into the wood, then it can cause the bar pop up and back at you. But if you are careful to keep the tip out of the wood and a firm grip on the saw and a well operating chain brake, there is no reason to be afraid of this chain. But for occasional ripping of small diameter logs, ripping for turning blanks can be done with a SHARP crosscut chain. Invest in the proper size round file and learn how to sharpen the cutters and file down the rakers. A SHARP chain will rip nicely.

This is good for starters but Allan doesnt sell chain:

http://www.chainsawsforsawmills.com/sawchains.htm

Granberg sells ripping chain, here is a LOT of detail:

http://www.granberg.com/ripping_chain.htm

Check out www.baileysonline.com or 1800 322 4539 and request a free catalog. They sell the chain you are looking for. Search on their site for part WP375 30RP.

from the part description:

"Ripping chain is specifically designed to cut efficiently with the grain of the wood, unlike standard saw chain. It is most commonly used to slab logs, burls and stumps. Most people use it with chainsaw powered sawmills such as the Alaskan Sawmill (Part Number 46776)or Beam Machine (Part Number 46100). Ripping chain gives you a smooth, consistant surface when cutting parallel to the grain of a log. On the contrary, standard saw chain is designed to sever wood across the grain, and when you saw parallel to the grain, your cutting speed falls dramatically, and your sawn surface becomes very rough.

30RP is our most common ripping chain. This ripping chain is used on bars from 16" to 32" long. The top plate of the semi-chisel cutter is ground at a 10 degree angle, while the side plate is ground at a 75 degree angle. 30RP is .375 pitch x .050 gauge (1.3mm). 30RP fits saws using Oregon® 72 series and Stihl® 33 series chain. 30RP chain sharpens with a 7/32" round file or 3/16" grinding wheel. This chain is recommended for milling purposes only. It is not designed for standard hand held use.

Priced per Drive Link

We will build a chain loop with the total quantity you enter

WARNING:All WoodsmanPRO™ saw chain is capable of kickback and could result in serious injury to the saw operator or bystanders. Do not use this chain unless you are experienced in dealing with kickback."

-Tim

Re: Chainsaw Blade Question.

#13

Re: Chainsaw Blade Question.

jeff jilg

>I use regular prosumer chain for all cuts. And I've processed a lot of wood. When ripping I try to hold the saw 3 or 4 inches out from the log, and I take a light cut. This allows some of the ribbons/slivers to fall to the ground, and it reduces the number of clogs in the head.

I only do this technique with heavier logs, which are unlikely to catch on the blade. And I'll repeat that I take a light cut with the saw not running full throttle. A rip cut is very efficient and it should go quickly.

Totally agree with Dick Hines - DO NOT clear the ribbons/shavings with your hands while the saw is running. It's tempting because clogs are frequent. One trick I use to remove clogs is to let the saw go to idle, then I make 1 or 2 teeth catch on a corner of a log and drag the blade in the opposite direction. It will pull out some of the clogs.

Be careful and be safe. Never touch the blade with the saw running even at idle.

...Jeff

...Austin, TX