Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Need a tree taken down or milled?

My Steady Rest *PICS*

Posts

My Steady Rest *PICS*

#1

My Steady Rest *PICS*

William Duffield, on the Cohansey

>This is in response to the thread below, started by Mike Recciione, in which he is looking for a design for a steady rest for a lathe with a small swing.

I designed and built this steady rest, based on Herman de Vries design, to be used on a JET 1236 and also on a 10' long homemade, mostly wooden bedpole lathe, which also has a 12" swing. It works for small spindles, large spindles, and hollow forms. Mike provided a link to Herman's rest in the previous thread. The biggest difference between mine and that one is the carriage. Mine allows a larger diameter turning to be supported than if the carriage were directly under the bars that hold the wheels.

Since I didn't have a hollow form in the shop to illustrate, I mounted a carving mallet between centers, just as a point of reference. I didn't need the steady rest, of course, to turn this mallet.

View from the headstock:


View from the tailstock:


View from the side, showing adjustments. This shows that there is room to drop the lower bar all the way to the bed, allowing a much larger diameter piece to be steadied. Also, note that a 12" toolrest can suport a tool all the way to the center line of the wheels. Of course, the supporting threaded rods would get in your way the last couple inches or so.


The fixed and moveable carriages are made from 8/4 hard maple. The allthread that supports the beams holding the wheels is bolted to the carriage with nuts top and bottom. The tops of the threaded rods got missed in both photos. It goes up a couple more inches and stops. The 4 smaller bolts at the corners are just to hold the carriage together. They should be supplemented by glue, once you have gotten all the kinks worked out of yours.

Two bolts in the carriage attach to these bedway clamps, which go under the bed. The boltheads are countersunk in the timbers, for additional clearance. I was too cheap to buy a couple more cast iron ones from JET, so I made them from maple.


For the bedpost latheosaurus, whose bed is made from a pair of 3x12s, the bolts are extended using the same hardware we use to secure the toolrest banjos.



As I noted to Mike in the previous post, we had a rather spectacular failure turning some long, thin spindles on the bedpost lathe, using old rollerblade wheels. I finally got a good look at the wheel this evening.


I have no idea. I wasn't there when it happened. The guy who did it is new to the art of turning, and it was his first use of this or any other steady rest. There's no use asking him what went wrong. He doesn't have much empathy with the turning tools yet. Maybe a bearing froze. There is severe damage to the hub as well as the tread.

Anyway, after the spinout in turn three, he limped back to the pits and replaced the wheels with smaller diameter, harder skateboard wheels, with high temperature sealed bearings, and completed the job without further incidents. There is one wheel in the upper bar, and two wheels in the lower bar.


Note the cutout he needed to make in the lower beam, to accommodate the smaller wheels and also very small diameter spindles.

With its approximately 2" square timbers and 3/4" diameter allthread and nuts and washers, this is probably more robust than would be needed for Mike's Delta Midi, but when you turn on the lathe, a 9 foot long 4x4 gets your attention real fast.

Re: My Steady Rest *PICS*

#2

Re: My Steady Rest *PICS*

Jim Shaver, Remote in SF!

>Wow,

That looks VERY stable...great idea and design!

Take care,

Jim

Re: My Steady Rest *PICS*

#3

Bill, this is great

Mike Recchione

>I was also planning to modify Herman's design so that the cross-bar with the two wheels could come down lower (as you did). I was thinking about using steel angle stock to create the base that goes across the lathe bed, but I think the way you approached it is at least as good and maybe better. Are there situations where you'd want to get closer to the steady rest, either with the tool rest or the tail stock than the wooden supports you used would allow?

The picture of that destroyed wheel was a little scary. Is there any chance that your friend got too close to the wheel with a tool while it was spinning? If not, I wonder if using the wheels from a cheap skateboard is really a great way to go - the bearings on those things can't be all that good. Although, a number of people have reported using recycled or cheap wheels with no problem, so it does make you wonder.

In any case, I found a skateboard on The Sports Authority's website for $19.99, so I'll give it a shot. If they blow up, well - that's what I wear a face mask and leather apron for :-)

Thanks again,

- Mike

Re: My Steady Rest *PICS*

#4

Re: Bill, this is great

William Duffield, on the Cohansey

>The more I think about the evidence of the wheels, the more I think that the bearing failed. First it heated up, melting and deforming the central "spoke" area of the tire, then siezed completely, at which time, the turning blank heated the tire to almost liquid, deposting some of it on the "tread" area of the other wheels. Therefore, the best thing to do is spend your money on good, sealed bearings, not the cheap ones that they put in cheap wheels. If you have cheap bearings, just pay attention to their sound and their temperature, just like you would do with a live center tail stock.

I don't have a lot of experience with this steady rest yet. The issues you ask about are not really important when it's being used on a long bedpost, since there's lots of room to move it back and forth. The biggest PITA is adjusting all the nuts every time you have to move it, especially when turning a tapered cylinder, like a typical bedpost, and especially with a large diameter turning, where you have to get a wrench between the sides of the carriage.

Re: My Steady Rest *PICS*

#5

Scary!

Mike Recchione

>It's interesting that, if you poke around the web, just about everyone seems to make steady rests using recycled wheels. I guess that doesn't say anything about how good the wheels were to begin with - recycled high-end wheels may be better than brand new el-cheapo wheels.

MSC has sealed bearings that look pretty decent (to me, at least) for less than $10 apiece, so that may be the route to go. Sheesh! Who ever thought the wheels would turn into such an issue? I tell ya, when all I used was hand tools, I never had to worry about my tools burning themselves up and throwing stuff all over the shop.

But better safe than sorry, I guess. So MSC it is. I guess I might as well pick up some drill rod to make reamers and D-bits out of while I'm at it. I have a feeling that by the time I'm done, this recorder will cost about 5 times as much as it would have to buy it! (But hopefully, they'll get cheaper as I go along. And then there's the flutes, and pennywhistles, and ... yeah, that's the ticket. It's an investment is what it is :-) )