Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Lathe lighting

Posts

Lathe lighting

#1

Lathe lighting

CapeMayMike

>Here's a pic (I hope) of a recent addition to my lathe, a new light. I have a 3 bulb flood suspended over the lathe, throws a lot of light but bakes my head, particulalry in the summer. I also have a 3 bulb flex neck to the rear of the lathe, throws a lot of light at the base of work but not over the top or near the headstock. Recently I found an articulated light in a neighbor's trash, being a trash picker I grabbed it. In the shop I foudn that it works just fine, I drilled and tapped 4 holes in the headstock of my Vicmarc and mounted it with machine screws. Works great, it's fully adjustable and can put light where I need it and it doesn't fry my brain! I know that various turners have inquired in the past abut lighting so I thought I'd share this.


img

Re: Lathe lighting

#2

Re: Lathe lighting

Brian Hahn in SW Wisconsin

>I really like those adjustable-arm lights. I recently bought four more (less than $10 each) for my lathe and workbenches. I like to use reflector spot light bulbs in them. The smaller reflector bulbs for used of accent lighting work best -- the standard size ones are too heavy the light tends to drift down.

Re: Lathe lighting

#3

I use one of those

Carole in VA

>Just be carefull about the shavings getting in there!

Re: Lathe lighting

#4

Re: Lathe lighting

Barry Irby

>I'm thinking of contacting a company that remodels dentist's offices and see if I can buy on of those lights they use (used and cheap). Anyone know whether they would be good lathe lights? Of course it might change the Ambiance of the shop.

I bought a little high intensity light from K-mart for about $7 or $8 and it works great. Has a clip on base. Never thought such a cheap light would last two or three years.

Re: Lathe lighting

#5

Re: Lathe lighting

CapeMayMike

>Somewhere online I recently saw photos of someone using exactly that, a dental light. Appeared to work just fine. Sorry, can't remember where.

Re: Lathe lighting

#6

Re: Lathe lighting *LINK*

JKJ in East TN

>Dave Peebles posted a photo of his dental light in January 04

http://www.woodcentral.com/cgi-bin/archives_turning.pl?read=26817

I use the cheap swing arm lights in combination with a number of inexpensive clip on "brooder" lights spaced around behind, above, and to the side. (Using the new fluorescent bulbs in some reflectors cuts way down on the heat.)

The only spot not well lit is direcly in front of me. I sometimes think of developing a chest light or maybe a reflective tee shirt. :)

JKJ


dental light thread

Re: Lathe lighting

#7

Re: Lathe lighting *LINK*

Gary Evans Tallassee, TN

>Since we're on the subject of lathe lighting, I was on the CME-Tools website the other day and saw a light with a magnetic base that looked useful for the lathe. It was pretty cheap, too. I don't remember exactly where it was listed, perhaps with the magnetic bases for dial guages.

Gary


Magnetic lathe lighting

Re: Lathe lighting

#8

Re: Lathe lighting

JamieDonaldson

>Be very careful using fluorescent lights for turning- there is some foundation to the speculation that the strobing effect can trigger epileptic seizures in susceptible individuals. My little bro is a neurology researcher and has confirmed this potential hazard. And I recall that someone posted about the very expensive replacement bulbs for a dental lamp?

Re: Lathe lighting

#9

Re: Lathe lighting

Bob Clancy from NM

>I use the cheap swing-arm lights like in the photo.... but have it mounted on the workbench on the opposite side of the lathe from me. Swing is extended with a little pivoting foot-long board that has a half-inch hole in one end for the light's base, and the other end has a dowel glued (protruding vertically downward) that goes into a hole in the workbench. It'll swing around in about any position you'd want, including shining on the front of the piece.

Above is a clip-on reflector lamp, 'tin' reflector with a regular 100-watt bulb, again on a board that pivots back & forth. The two give good light for doing the outside of a piece, for the inside, I turn off the overhead light and just use the swingarm lamp.

Lighting is SOOOOO important!

Re: Lathe lighting

#10

Re: Lathe lighting

Eric Kuehne

>Barry,

I recently saw Woodworks show with a turning project (or maybe a shop tour). David Marks made a point of showing off his dentist light. Seems like a pretty good endorsement to me.

Good luck. I, for one, would be interested in hearing how your hunt turns out.

Eric

Re: Lathe lighting

#11

Re: Lathe lighting *LINK*

Carol Reed, the Router Lady, Dubuque

>Here is an option from Northern Tool, if the dental lights are too pricy.


dock arm light