Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Nearly 100 Exotic Wood Species, Direct-Imported Since 1972. Shop Slabs & Turning Stock.

Bill Grumbine's record remains intact...

Posts

Bill Grumbine's record remains intact...

#1

Bill Grumbine's record remains intact...

Ted Owen, Pittsburgh

>...I'm a little disappointed to say. That guy could stop a freight train.

Bill was over on our side of the state this morning and stopped in for some quality turning time on my new lathe, a VB36. He had not yet tried out a VB, which I bought when the Poolewoods became unavailable.

He said he has never worked on a lathe he could not bog to a stop, but I was guessing he was about to meet his 3-h.p. match. In fact, I would have bet money on it. No such luck--a very unbalanced, slow-turning 23" x 6" piece of walnut teamed up with Bill's turning muscle to humble the mighty VB. It was a sad moment for the home team.

I'm telling ya, this guy could stop a train.

Great to see you again, Bill. And thanks for all your help and guidance, especially the coring demo.

Best, Ted

Re: Bill Grumbine's record remains intact...

#2

Re: Bill Grumbine's record remains intact...

JamieDonaldson

>That wasn't a fair test- crank the RPM's up to max torque range and then try it, but don't hurt yourself!

Re: Bill Grumbine's record remains intact...

#3

Re: Bill Grumbine's record remains intact...

Bill Grumbine (Kutztown PA)

>Actually Jamie, I think it was going pretty close to the top end of the speed range when I slowed it down. There is no speed indicator on the lathe like there is on my Poolewood, but that bowl was moving at a pretty good clip. It had been rounded out and was about 99% true, and I had cranked it up to see what it would do. I was using a Glaser 3/4" gouge.

I had a great time at Ted's place, and the VB is a very nice lathe to use. SWMBO got to see it in person last time we were out to that end of the state, and on the way home, I was informed that I was not even to THINK about getting one. I told Ted that there are not many times when I can tell someone that their lathe makes mine look small. ;-)

Bill

Re: Bill Grumbine's record remains intact...

#4

I also have a hunch...

Ted Owen, Pittsburgh

>...you had extra turning muscle available in reserve. : )

I'll have to try it myself sometime with the belt in a more torque-ie position. (It was in the middle of three ranges.)

Hope your glasses have arrived by now, 10:30 a.m.

Best, Ted

Re: Bill Grumbine's record remains intact...

#5

Re: Bill Grumbine's record remains intact...

JamieDonaldson

>Let's see if I have this right, Bill. He let you do all the roughing dirty work, and you left him a nice smoothed bowl to finish? What a deal!!

Re: Bill Grumbine's record remains intact...

#6

Put the belt on the small pulley and...

TDaniel

>the lathe may spin around but it won't stall.:)

Re: Bill Grumbine's record remains intact...

#7

Yes, and...

Ted Owen, Pittsburgh

>...he then showed me how to use the Kelton coring system. Ended up with three rough bowls. Though one of them has a lovely drain hole in the bottom--that was my doing, not Bill's. Gonna need a little more practice with the coring system.

I almost got a nice pair of safety glasses out of the deal, too. Carrying pouch included.

Best, Ted

Re: Bill Grumbine's record remains intact...

#8

Re: Bill Grumbine's record remains intact...

Bill Grumbine (Kutztown PA)

>Ted, the glasses made it, and even in one piece. Thanks again!

Jamie, that is right, I had to do all the hard work, and then Ted took a few light cuts at the end. I do have to take some of the credit for the lampshade he made with the coring tool, since I was helping him aim it.

Bill

Re: Bill Grumbine's record remains intact...

#9

Re: Bill Grumbine's record remains intact...

Ted Owen, Pittsburgh

>"Light cuts" and "Ted" don't belong in the same sentence.