Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Rare Exotic & Domestic Hardwoods, Milled In-House in Oregon. Browse Unique Stock.

Wands and 'stuff'

Posts

Wands and 'stuff'

#1

Wands and 'stuff'

Molly Winton

>Given the name retention capacity of my brain (0 to none), I forget who I was talking to about making wands. I said I'd post a picture, so here it is. I've also included a couple other 'craft' items I've been cranking out for an upcoming annual Holiday sale. I've not made these items for some time, since focusing on my more artsy-fartsy creations. It's been fun doing production for (all the more fun knowing it's time-limited). Thanks to Ruth Niles for the scoop design, and if anyone knows where I can find more bristle blanks, please let me know!


img

Re: Wands and 'stuff'

#2

Re: Wands and 'stuff'

Jim Shaver, Remote in SF!

>Hi Molly,

These all look really fun! I like the combinations in the wands..

cool!

take care,

Jim

Re: Wands and 'stuff'

#3

Re: Wands and 'stuff'

Carole in VA

>Cool stuff, Molly. Craft Supplies USA has the bristles. Look under Kitchenware.

Re: Wands and 'stuff'

#4

Re: Wands and 'stuff'

Gary Ljostad

>Neat stuff Molly. Speaking of Ruth, she brought one of your pieces to Totaly Turning in Albany NY, last weekend. All I can say is outstanding. They are super in photos, but much better in person. Ruth put it in the instant gallery and it receaved a tremendous amount of attention, including the critique by Andi Wolfe and Stuart Batty. Nice going Molly

Re: Wands and 'stuff'

#5

JL

Re: Wands and 'stuff'

JL

>I plead ignorance - I use bristle brushes to brush on oil and egg whites. What is the intended use of the scoops?

Re: Wands and 'stuff'

#6

Looks like coffee measures to me ...

Fred in NC

>

Re: Wands and 'stuff'

#7

Re: Wands and 'stuff'

TomW in SouthJersey

>Molly - It was me that you were talking with about the wands for the upcoming Harry Potter movie release. Those look very nice. I also like the two color design.

Thanks for posting. You remined me I need to get started on more wands.

Tom Wright

Re: Wands and 'stuff'

#8

Re: Wands and 'stuff'

Ruth Niles

>JL, they are coffee scoops. I originally got the idea from old seed scoops that were used 100 years ago when seeds were sold by the pound. They had various size scoops to accomodate various size seeds so one scoop would equal approx. the same weight in seeds. There's a very old general store near me and the grandfather still has the seed scoops there, handmade from wood, too. Molly's scoops are 1/8 cup, which is your standard coffee measure (at least they should be!).

Ruth

Re: Wands and 'stuff'

#9

Re: Wands and 'stuff'

Jennifer@Indy.USA

>Molly you Rock! These are great looking "crafty" things. Your spindle work is fantastic. I've come to the conclusion that me and spindles don't get along. It takes me an hour and a half to make a one piece wand. Ugh....at that rate I'll have to charge $50.00 for them!

Good luck at the Holiday Show. I'm sure you'll do great!

Jen

Re: Wands and 'stuff'

#10

Re: Wands and 'stuff'

William Duffield, on the Cohansey

>I understand completely, but with practice I'm getting faster. Too bad I can't just shake one of the finished ones at a blank and have another one. Nope, don't want to do that. Micky and Dukas taught us that lesson many years ago.

I find it takes me less time to make a two piece wand. Less whip means I can turn faster, with fewer broken shafts. Mounting the predrilled stock on a mandrel means I need less pressure (almost none) from the tailstock, also resulting in less whip. It is much easier to finish one end of a short stick while on the lathe than to try to part off both ends of a long stick and get them both smooth. The unfinished end then just butts up against the other unfinished end, and both are invisible. To assemble them, I cut a bunch of round steel stock in two inch lengths with a hacksaw, and put them together with a couple drops of super glue. Also, I can offer the magician a choice of headstock and tailstock :^) and assemble a custom wand on the spot. I can also install a hand blown glass bead between the handle and shaft for almost no additional labor.

Re: Wands and 'stuff'

#11

Re: Wands and 'stuff'

Jennifer@Indy.USA

>Great ideas! Thanks.

Re: Wands and 'stuff'

#12

Re: Wands and 'stuff'

Molly Winton

>They are, they are! I keep a coffee scoop of rice at the lathe and check each one to make sure they're the right size prior to finishing. If I goof and make the scoop too big I score a 'fill' line where the correct measurement should be. Luckily that's only happened twice. They're fun to make, and make a great novelty gift. I often tie one to a sample pack of coffee. Super hostess gifts.

Re: Wands and 'stuff'

#13

Re: Wands and 'stuff'

Molly Winton

>(Slap on forehead!) Of course Tom, NOW I remember. Thanks, these are quite fun to make. I turn the wand portion from a 3/4" dowel (that's what I had on hand), but you could get away with a 1/2" dowel. I like to make the detail at the connector end and then taper from there to about 1/4". The handles are from approximately 1" square x6" blanks, similar to the brush handles.

Re: Wands and 'stuff'

#14

Re: Wands and 'stuff'

Molly Winton

>You're not alone Jennifer, my spindle work is pretty lame too. You've just seen the extent of what I can do. I've finally got the handles (wands and brushes) down to about 10-12 minutes each, but even that's super slow compared to good spindlers. It's just a matter of doing it over and over and over. I still haven't mastered the skew, which I understand makes this work go even faster. I use a roughing gouge to get down to a rough form (it's quite fast), and then finish with my 3/8" Glaser detail gouge.

Re: Wands and 'stuff'

#15

Re: Wands and 'stuff'

Ed Moore

>Molly,

Consider using a Sorensen Spindlemaker in the Hamlet lines carried by Craft Supplies USA for finishing spindles. I turn lots of red oak dowels into "icicles" for my Christmas ornaments. I may rough with a roughing gouge or spindle gouge, but I final shape or smooth the extremely thin parts with a Spindlemaker. Of course, the secret is to begin with the right end and once a part is finished and there is a thin part to the left, you never go back with a tool again. And you sand each little part after it is completed rather than all the icicle at once. Of course the deep vee cuts are made with a 1/4" round skew.

While I like many Sorby tools, I do NOT like the Sorby Spindlemaster. It is too thin and has too much whip for me.

The Spindlemaker is less aggressive than a skew and leaves a polished surface. It's one of my "Don't leave home without it!" tools.

Re: Wands and 'stuff'

#16

Re: Wands and 'stuff'

Jennifer@Indy.USA

>Ed, thanks for the advice....I may have to look into one of those. I've always thought I needed to try the Spindlmaster...but perhaps I'll look at this one you suggest instead. I need all the help I can get!

Jen :)

Re: Wands and 'stuff'

#17

Thanks Ed, I'll check that out!

Molly Winton

>

Re: Wands and 'stuff'

#18

???on Spindle maker

Spence in Rhode Island

>I just looked at a pic of the tool in a catalouge and the tools looks like a scapper with a long grind to it. I take you use it with the bevel rubbing. Are there any other differences between it and a scrapper? Sorry to bother you with a question.

Regards

Spence

Re: Wands and 'stuff'

#19

Re: Wands and 'stuff'

Spence in Rhode Island

>Molly. They all look fantatic! A question on the scoops. Do the handle tenneons go all the way thru the wall of the scoop and about how thick is the wall? When I make mine I don't peirce the wall but I always worry about the handle not being secure enough to handle heavy use.

Thanks!

Spence

Re: Wands and 'stuff'

#20

Re: ???on Spindle maker

Ed Moore

>Spence,

Although you may choose to use the Spindlemaker as a scraper, it will probably dull quickly when so used. Rather, use it as a skew with the bevel rubbing and you will get a very smooth cut. I would not use it to make a vee cut, like a skew is often used, but it is great when making a concave cut "down the grain". Remember, this is a SPINDLEmaker, so the grain should be parallel to the axis of the lathe. I have never tried to use it when dealing with a bowl-orientation (cross-grain). My suspicion is that using it on a bowl could lead to the Mother of all Catches.

Spindlemakers should be sharpened properly and then honed. I use a piece of circular MDF mounted in a chuck to hone. There are honing compounds that can be applied to the squared edge and then one can polish the surface. I stand on the back side of the lathe so that it is turning AWAY from me when I hone tools. I bought some Tormek honing compound that I use on this wheel.

Re: Wands and 'stuff'

#21

Re: Wands and 'stuff'

Phil Joines Krum, Texas

>Molly,

Nice work. Have you thought about making the hole in the wand handle go most of the way through? With a tennon on the blade to keep it in place they would have a "Secret Compartment".

Re: Wands and 'stuff'

#22

Re: Wands and 'stuff'

Molly Winton

>Hi Spence. The handles do go all the way through the bowl. I round the end so it looks more finished. The thickness of the bowl is about 3/16".

Re: Wands and 'stuff'

#23

That could be cool!

Molly Winton

>

Re: Wands and 'stuff'

#24

Re: ???on Spindle maker

Spence in Rhode Island

>Thanks Ed! I'll have to make one and give it a try. I know for a fact thats it not a good idea to try it on a bowl. ;) DAMHIKT LOL Have some 5/8"x1/4" HSS flatstock that has been begging me to use it for something.

Thanks again

Spence

Re: Wands and 'stuff'

#25

Re: Wands and 'stuff'

Spence in Rhode Island

>Thanks Molly! Never thought of rounding the ends. Sounds like its time for a design change. LOL