Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Support WoodCentral when buying things you need

Sorby Hollowmaster revisited

Posts

Sorby Hollowmaster revisited

#1

Sorby Hollowmaster revisited

DWFII

>I have a further question...I went to change the cutter on my Sorby to the right side as you depict in your photo, but the back end of the cutter sticks way out past the shaft of the tool. This would make hollowing through a small opening extremely difficult or even hollowing "around the corner," if you know what I mean, almost impossible--under the shoulder of a tall tapered vase for instance.

What am I missing? Configured like this, the tool seems less versatile than witht he cutter on the left side...but I haven't tried using it with the cutter on the right side yet so I can't even say if it cuts better.

Please comment...anyone...

DW

In the High Desert of Central Oregon

Re: Sorby Hollowmaster revisited

#2

Re: Sorby Hollowmaster revisited

DWFII

>Sorry for the duped message...I didn't see the other one at first.

DW

In the High Desert of Central Oregon

Re: Sorby Hollowmaster revisited

#3

Re: Sorby Hollowmaster revisited

RK in Milw

>You can slide the cutter so it sticks out the front and not out the back. I have some cutters that have gotten shorter due to use. To get under shoulders, pivot the cutter and the tool until the tip points to where you want to cut.

Hope this helps. If not, keep asking questions.


img

Re: Sorby Hollowmaster revisited

#4

Re: Sorby Hollowmaster revisited

DWFII

>Iunderstand... and thanks...but unless the cutter is really short and the hole through which you are hollowing pretty large (as well as the interior of the vase being pretty large) if the backend of the cutter is sticking out, it seems to me you've got a major catch in the offing. Do you stick the tool inside the bowl/vase before you turn the machine on? That would be scary!

Is it possible to hacksaw one of these cutters in half? Or cut a third of the length off...something like that?

Re: Sorby Hollowmaster revisited

#5

Re: Sorby Hollowmaster revisited

Mark Kauder, Phenix City, AL

>I have had far more problems (catches) getting the the tool in and out with the lathe running. IF the opening is small, I regularly put the tool in - making sure it is clear of everything, and then turn the lathe on. Same goes for taking it out - especially if it is all wrapped up with shavings. I get it completely clear of the sides and mouth, and then shut the late off and wait for it to stop.

Same goes for my non-powered rotary sander,

Just my opinion.

Mark

Re: Sorby Hollowmaster revisited

#6

Re: Sorby Hollowmaster revisited

Mark Kauder, Phenix City, AL

>P.s. This goes for all my hollowing tools - Hollowmaster (still my favorite), Sorby Swan-necks (all sizes), and my Don Pencil system.

Mark

Re: Sorby Hollowmaster revisited

#7

Re: Sorby Hollowmaster revisited

Carole in VA

>I NEVER try to put a hollowing tool into or pull it out of a small opening with the lathe running! Yes, that's a lot of starting and stopping, but it doesn't take but a split second to ruin the piece (or yourself) if you catch it while the piece is spinning. If you are unsuccessful with haksawing a cutter, you could grind one down. I find that mine get short soon enough because I like sharp bits and probably overdo it on the grinder.

Re: Sorby Hollowmaster revisited

#8

Re: Sorby Hollowmaster revisited

Molly Winton

>This is such a timely thread. I've been thinking about getting the mini Hollowmaster. I want one that has no more than a 1/2" shank, with a swan neck. This looks like the ticket, and all of this advice cuts my learning curve way down. Thanks Carole!!!

Re: Sorby Hollowmaster revisited

#9

Re: Sorby Hollowmaster revisited

DWFII

>Put the tool in before your trun on the machine??!! Who knew?! I have a Jet mini/midi and the on/off switch is there on the lower right hand side of the machine. I have to let go of the Hollowmaster with my left hand and kind of reach underneath myself feeling for the switch to turn it on. This made me very nervous because it seemed the tool could inadvertantly shift...as it was only being held with one hand and the body was doing a little bit of twisting...sort of.

I'll have to try it.

Just as a matter of curiousity what is the smallest opening that a person of limited experience could reasonably expect to work through with the Sorby Hollowmaster? The same size as the tool?

DW

In the High Desert of Central Oregon

Re: Sorby Hollowmaster revisited

#10

Re: Sorby Hollowmaster revisited

JamieDonaldson

>The hole always has to be somewhat larger than the tool, even with turning the motor off for inserting or removing the tool. If the tool shaft whacks the rim while turning ,you can count on it cracking or splitting the wood. The idea of hacksawing the HSS tool bits won't do- use a cut-off disc on a Dremel, and hold it in a vise.

Re: Sorby Hollowmaster revisited

#11

Re: Sorby Hollowmaster revisited

Mark Kauder, Phenix City, AL

>I agree with Jamie. My guess is the hole would have to be some where around 50-100% larger than the tool shaft. Even at that size, the big problem is evacuating the chips.

Speeds in the HHS range or harder require abrasive cutting. A file or toothed tools will not touch them.

Mark

Re: Sorby Hollowmaster revisited

#12

Re: Sorby Hollowmaster revisited

Wally Dickerman in Arizona

>DW, If the on-off switch on your lathe is so far from your position when turning that you have to shift your body and reach for the switch while the tool is inside the hollow form, to either turn the lathe on or off, then that is a dangerous thing to do. I regularly do this myself but the switch on my lathe is just above the spindle and I can reach it easily without moving my body or taking my eyes off the turning piece.

Wally

Re: Sorby Hollowmaster revisited

#13

Re: Sorby Hollowmaster revisited

JimQ

>It is easy enough to get a foot switch extension cord to use as a secondary switch. I have one that the lathe plugs into, then it plugs into the outlet. I can turn the lathe off with my foot if I need to. If you need to start with it, make sure it's off, and turn on the lathe get everything in place and then step on the switch. If you have a magnetic or relay switch, the start up will not work remotely, but the shut down will.

JimQ

Re: Sorby Hollowmaster revisited

#14

Re: Sorby Hollowmaster revisited

DWFII

>I guess I don't need to tell you all how helpful this is. I didn't start this thread but I sure appreciate it...it's given me a lot of confidence and an enthusiasm to get out there and finish up a couple of HF's that I've had roughed out for a while.

thanks to all

DW

In the High Desert of Central Oregon