Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Knitting Needles

Posts

Knitting Needles

#1

Knitting Needles

Rick Allen

>Hi

I made a bunch of wands a while back. I showed the wands to a co-worker and she exclaimed how they looked a little like knitting needles. So I asked her about knitting needles. She says she currently is using size 8. Well a size 8 is a 6mm shaft. That is larger than most of my wands so I though this would be easy. About a Turns out that knitting needles are more difficult to make than magic wands. My wands are tapered. I don't much care about the rate of taper, just that the tip is smaller than the handle end. But with knitting needles the shaft needs to be of a consistent diameter. I guess the first few inches could be consistent and the diameter could be smaller after that. Anyway my first try yielded a 5mm shaft. Oops a size 7 knitting needle. The second one broke. The third one was 4mm which is a size 6. I tried one more. Another size 6 well at least I had a pair. I gave up for a few weeks while I tried other things. So this weekend I tried again. First one broke, second one was a size 7 (great now I have two pair) and the last two I managed to make 6mm which is the size 8 I was looking for.

The stops on the knitting needles was another effort. I wanted to make tiny flowers. Fat chance. Instead I decided to make the stops for like needles out of the same material. I needed some way of "displaying" the needles so the tall vase was selected as a good shape. I had some 16/4 Brazilian cherry on hand. Another bad idea. That stuff hollows like concrete. Or at least that is how it worked in my hands. So the hole is primarily drilled with a ship auger.

The stock I was working from for the needles was 14" long and 13" long. I lose about 1/2" to the mounting so the thin needles were 13 1/2". The larger needles were 12 1/2" long. I wanted them all the same length so they are all 12 1/2" long.

I hope the lady likes the needles. It will likely be a while before I make any more. My understanding is that using wood needles feels better than plastic or metal needles. I wonder if the needles will hold up to use for very long.

Thanks

Richard


img

Re: Knitting Needles

#2

nother

Rick Allen

>Her is a picture of the needles, size 6 on the left


img

Re: Knitting Needles

#3

Re: nother

JKJ in East TN

>Rick,

Yikes, you've got some twisty grain on some of those - very hard to turn without breaking. The worst thin shaft I ever tried was from a maple burl - I found it impossible! You might try looking for wood with very straight grain. Perhaps even split pieces off some 4/4 boards to be sure the shaft follows the grain.

Are you turning these between centers or with one end gripped in a chuck? One thing I found helps a LOT when turning thin shafts is to hold the driven end firmly in a chuck. (I actually turn a morse taper and jam it into the headstock spindle for the same effect but for more working room than possible with the large chuck.) This seems to help a lot by preventing the shaft from flexing as much. When I try to turn between centers, I break a lot of pieces - three in a row one night. When I grip one end tightly, breakage is rare.

Those needles look great. I've been making some hair sticks which are not nearly as long. I might have to try some knitting needles.

JKJ

Re: Knitting Needles

#4

JL

Re: nother

JL

>Of course ya'll are both crazy - you realize that don't you? That's what they have dowel makers for. Good work Rick. They are pretty needles. I'll stick with yarn ballers. They are much larger in diameter.

Re: Knitting Needles

#5

Turning dowels *LINK*

Fred in NC

>A steady rest for dowels will help a lot. This is very common with metal turners (called machinists!). David Reed Smith came up with a great idea in the link below. All you need is a piece of UHMW, some scrap wood, bolts and a wing nut. UHMW has very low friction and is ideal for this.


Steady rest

Re: Knitting Needles

#6

Re: Turning dowels - more ideas

Fred in NC

>It makes a lot of sense to start with a dowel. I made some drop spindles and used "hardwood" and oak dowels from the borg. So called hardwood dowels don't have the species listed, and it can vary from batch to batch and which store you get it, but are usually good.

8 mm = .315" and 5/16" = .313", which is less than the thickness of a piece of paper undersized. Besides, I found that most commercial dowels are a bit oversized. A little sanding will bring it to size if you need it that precise.

For 6 mm use 1/4", which is just a bit oversized.

It is easier to turn thin spindles when you can chuck them with only a couple inches sticking out. Of course this limits the stock size to what can fit through the hole in my spindle (3/8").

I chuck the dowel with about an inch sticking out, and drill a center hole with a center drill. Center drills are very useful, since they make a hole with the 60 degree taper in them. Then chuck the dowel with 2-3" sticking out, with the live center at the other end, and turn to almost finished size. Then pull out another 2-3" and turn it down. Sanding takes care of the finished size and any marks.

One of my most useful tools is an old fashioned machinist's caliper. I mean the simple kind with no dial or digital readouot. I open the jaws to the required finished size, lock it, and use it to check the diameter along the way.

Hope this helps.

Re: Knitting Needles

#7

Good info here on turning thin, uniform shafts  *LINK*

Dave Smith, Longview, WA

>


Larry Hancock Crochet Hooks

Re: Knitting Needles

#8

Here's a way to cheat just a little

Garrett in Victoria

>Lee Valley sells 2 different kits for making dowels. The first is simple and inexpensive, and the second is just the opposite.

The smaller units will deliver a close enough cylinder to permit easy finishing to final dimension. And to legitimately claim that they have been turned. (Twice.)

Cheers, Garrett

Re: Knitting Needles

#9

Re: Here's a way to cheat just a little

Rick Allen

>Those look great except the more expensive unit will do is 1/4". That translates to slightly larger than 6mm. The largest knitting needle was just under 6mm with the smallest being 4mm.

Woodturning is a hobby for me. Faster isn't necessarily what I am looking for. Spending time listening to the sounds of the lathe as a sharp edge cleaves curls off the spinning wood is music. The smells of the woods and finishes, the transformation from rough turning stock to a beautiful shiny surface, the joy of making something with my own hands and skills for someone special to me, testing my skills and developing workarounds while my skills try to play catchup with my imagination. Those are some of the things that find me standing in front of the lathe most evenings.

I think I will let someone else make a living at creating wooden knitting needles.

Thanks

Richard

Re: Knitting Needles

#10

Richard that is pure poetry.

Ed Karch in No.VA

>