Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Price drop on over 1300 Rockler items

Bandsaw Help

Posts

Bandsaw Help

#1

Bandsaw Help

Doug Reynolds in Seattle

>I harvested some fresh cut soft maple and tried to cut the blanks into circles on my Mini Max 20 bandsaw with a new 1/2" blade using a circle cutting jig. The blade wanted to track toward the inside of the cut, never meeting at the cut entrance. The blanks were in the four to ten inch diameter range. Size did not seem to make a difference.

Also, the blade would get all gumed up from the wet wood, almost "strings" hanging from the blade teeth. Any fix for that short of stopping every few blanks to clean the blade?

What is your preferred blade for this purpose? Maybe I don't have the right one.

Re: Bandsaw Help

#2

Re: Bandsaw Help

RK in Milw

>1/2" is way too wide a blade for such a small radius. Try 1/4" or even smaller.

Re: Bandsaw Help

#3

Suggestion...

Peter Teubel

>What kind of blade are you using? I would suggest a 3/8" 3 or 4 TPI hook tooth blade. I've found that 3/8" works best for me regardless of blank size. If you are cutting WITH the grain (i.e. log is standing UP on the table), you will get those strings...and if you go too fast, these strings can bind up in the guides. Also, forget the circle cutting jig. They don't work for thick green wood. You will always have blade drift and it'll just cause the blade to bend and bind. If you are cutting bowl blanks, a rough circular shape is more than adequate. Use your circle cutting jig to make various sized circles from 1/4" hardboard. Take your circle and just nail it to the top of the log and use that as your guide to cut.

Re: Bandsaw Help

#4

Re: Suggestion...

John Trant (Baltimore/DC corridor)

>I agree with Peter. The lathe is better at making "circles" than the bandsaw so free-hand saw the blanks to the approaxiamte size using a pattern or a compass as a guide. I use one of a series of circles cut from discarded paneling. Make sure you keep the large face of the split log down on the saw's table otherwise you could have a catch and break your band (or worse!).

John

Re: Bandsaw Help

#5

Re: Bandsaw Help

Greg in Oshkosh

>Sounds like you don't have the blade and the pivot on the circle jig lined up correctly. The pivot needs to be even with the front of the blade. If it's not the blade will want to track off of the circle. The best blades are Timberwolf AS blades in 3/8 width and 3TPI. This blade works better in wet wood because the set of the teeth is wider giving a wider kerf for the shavings to leave. I Talked to the Timberwolf people and the AS is the blade they recommended.

Re: Bandsaw Help

#6

Actually...

Brian Hahn in SW Wisconsin

>Actually, the position for the minimum radius is about 1/3 of the way back on the blade. The exact position depends on the width of the kerf and the thickness of the body as well as the blade width.

I was getting rather frustrated one time because the minimum radius I was getting didn't even come close to the published values. (More like 2x) So I decided to figure it out for my self. It's really a rather simple geometry problem and as they liked to say in the text books, the proof will be left as an excercise for the reader. ;-)

The bottom line is narrow kerf blades have a much larger minimum turning radius than wide kerf blades. Not really surprising, but you don't see it mentioned very often.

My personal preference is a 1/4" hook tooth blade with the pivot point lined up with the back of the teeth (bottoms of the gullet).

Re: Bandsaw Help

#7

Keith Tompkins

Re: Bandsaw Help

Keith Tompkins

>Hi Doug, like several others have posted, ditch the circle cutting guide, and use the saw freehand. In that way, the blank can float, relieving stress against the blade. You will bind and break several blades otherwise, and possibly create dangerous situations.

Always have a flat surface of the wood blank on the bandsaw table, and plan each cut. If you slip, you do not want your hand to be in the path of the blade.

Re: Bandsaw Help

#8

Re: Bandsaw Help

Barry Irby

>I made a circle cutting fixture. It was just a piece of half inch plywood with a stick that slides in the table slot. It was shorter that the table so that there were two rows of holes, labeled odd and even. I put a pin in the hole and slide the blank into the blade, aligning the correct edge with the front or rear edge of the table. Then I would just turn the blank in a circle. Worked fine until I changed blades. Basically has never worked again. Don't remember what blade I was using.

What does work though is to use it as a sled. I put the blank over the pin in the correct hole and just slide it past the blade. Pull it back, rotate the blank. and slice off another side. I can make an eight sided blank in a hurry and they run fairly true and let me move on. Doesn't take much longer to clean up an eight or twelve sided blank than a circle.

Re: Bandsaw Help

#9

Re: Bandsaw Help

Tony Shaftel

>I have a jig with a pin on a sliding piece for adjusting the radius; it works quite well. Also have a chart I printed from one of the popular bandsaw books that shows the minimum radius you can cut with each blade size. The other day I tried cutting a circle near the minimum radius for a 3/4" blade and forced it off the thrust guide, ruining it. Went to Eagle Tools to buy another and Jesse there told me he felt the minimums on the chart were way too small and just asking for trouble. The circle cut perfectly with a 1/2" blade.