Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Have a question? Ask Woody!

New bowls

Posts

New bowls

#1

New bowls

John Lucas

>Here is a spalted maple bowl with a limb pith left in. I filled the crack with black CA glue. Finished with walnut oil. I did something different this time. I applied the 2nd layer of finish with 600 grit paper and the 3rd layer with 4/0 steel wool. Then I applied a coat of Johnsons past wax. I like the look and feel.


img

Re: New bowls

#2

spalted maple bowl

John Lucas

>Here is another one. This one has a thinned lacquer finish buffed lightly with the beal and the shine was knocked down with a fairly course rag. Looks very natural but the Carnauba wax doesn't feel as good as the johnsons floor wax.


img

Re: New bowls

#3

Re: spalted maple bowl

Kevin Turner

>Nice look (top view). Q: while the CA glue prevent the knot from craking further? KevinT in T Bay..

Re: New bowls

#4

Re: New bowls

Devon Palmer

>Beautiful stuff John,

I love spalted wood, its my favorite stuff to work with (ok, it sucks to work with , but, I like how it looks). Of all the stuff in my shop, visitors always make a bee-line to the big spalted pieces.

How do you firm your stuff up and keep it from tearing out? I just started experimenting with Polycryl (some water based firming agent), but, have used everything from Sanding Sealer and turpentine to the Minwax wood hardener. Sharp tools and a little walnut oil on the cut seem to help as well.

- Devo

Re: New bowls

#5

Re: spalted maple bowl

George Van in WI

>Thanks John, finish #2 may be what I am looking for. I have a well spalted yellow birch bowl sanded and ready to finish. I was thinking of a finish similar to David Ellsworth’s Homage series and I think this will get me close. The other I was considering was Krylon fixative.

The walnut oil sure “pops” the grain in bowl #1.

Re: New bowls

#6

Re: New bowls

John Lucas

>Devon I try sharp tools and then spray it with water and then cut with a freshly sharpened tool. If that doesn't seem like it's working then I soak it with several coats of Lacquer thinned about 50/50 with lacquer thinner. Sometimes it takes this a while to dry the wood is really punky. It soaks in so far you have to but on many coats. If it's just a little bad then one coat will do the job.

It tends to clog the sandpaper so I spend as much time cutting and shear scraping as I can before going to the sandpaper. If all else fails I turn the lathe off and power sand just that area. That's a last ditch effort because even though you think you've blended this area into the rest of the bowl you can usually see it as an uneven reflection when the bowl is finished. On the plus side no one I've shown my bowls to has ever noticed. I guess I'm too picky.

I'm like you. It just isn't fun spending all that time trying to save the bowl when it's just a 3 inch area that is giving you problems. If the rest of the bowl didn't look so good I would just toss it.

Re: New bowls

#7

Re: spalted maple bowl

John Lucas

>George I like Krylon Fixatif. I haven't used it in a while. If you use the Beal buffing system you can have any look from matte to fairly glossy with this stuff. Haven't sprayed it over walnut oil so I don't know if they are compatible.

Re: New bowls

#8

Re: spalted maple bowl

John Lucas

>Kevin I never trust CA to stop a check. I let them sit for several days until the bowl is completely dry and done all the nasty things it's going to do then I resand the piece and decide what to do about the hole. In this case the pity already had some black so I filled it further.

In this case I might have been able to keep the cracks to a minimum or stop them entirely if I had put the bowl in a box or bag to slow down the drying. I was demonstrating outside on a very windy day. I think the wind and sun forced it to dry faster than it wanted and it cracked. made a good piece to show people when they ask, "Don't they crack when you turn them green". My answer is usually , yes if you don't do it right.