Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Precision you can feel — woodworking perfected with Lee Valley

Hollow form stock ?

Posts

Hollow form stock ?

#1

Hollow form stock ?

Pete in Holland, MI

>Hey all -

Am expanding into the hollow form area of turning and am curious on how to get larger "dry" blocks to turn from. Am looking to turn pieces on my Jet1236, so diameter is limited.

1) Do I Anchorseal chunks of green firewood for a year or so? Strip the bark from them first?

2) Do I split/saw blanks from logs and anchorseal them to prevent cracking during drying?

3) Will dry firewood be worth my effort looking for check free stock?

4) As with bowls, do I still need to stay away from the plinth?

Trees are not an issue around here. Just trying to figure out better means of starting the drying process yet this fall. Input or directions to past articles will be appreciated.

Thanx.........

Re: Hollow form stock ?

#2

Re: Hollow form stock ?

Molly Winton

>Hey Pete, one of the beauties of hollow turning is you don't really need to dry the wood prior to turning. If you endgrain turn, most often you can finish turn a piece (with uniform wall thickness), and you will have minimal movement, and should not have checking at all. Of course the normal disclaimers go here regarding some of the traditionally unstable woods. Just treat the green wood blanks as you would for bowl blanks. If you're not going to turn the wood soon after harvesting, anchorseal the ends. You can also rough turn a hollow if you want to make absolute sure there is no movement, again treating it similarly to a rough turned bowl. If you do side grain hollowing I do recommend rough turning, because chances are there will be more movement in this orientation. Good luck.

Re: Hollow form stock ?

#3

Re: Hollow form stock ?

Mark Kauder, Phenix City, AL

>A couple of points.

1) You are not going to find hard to find dry wood, very big.

2) Most people would rather get freshly cut green wood and then rough hollow it and then dry it (various methods). Green wood hollowing is soooooo much easier.

3)If you can get wood large enough, you can do your hollow form w/o any pith. If not, center the pith down the center of the hollow form. Some People drill out the bottom pith, and replace it with a plug from the same wood.

4) If small hollow forms are what you are looking at, Dry slit firewood is a good source.

Just my opinion and experience.

Mark

Re: Hollow form stock ?

#4

Re: Hollow form stock ?

John Lucas

>It is difficult to find large dry wood. My local wood store just got some 6"x 10" dry buckeye. They will cut it to length. $1.25 a bd.ft. I doubt that they will ship however. If you happen to be in Middle Tennessee look me up and I'll show you where they are.

Re: Hollow form stock ?

#5

Turn green and soak in alcohol. PIC

Dave Smith, Longview, WA

>Hi Pete,

Aren't you the guy who couldn't dry white oak bowls without cracking? If you are then maybe you won't believe me about alcohol. I don't turn very large hollow forms because I am hollowing tool challenged. For small hollow forms turn to about 1/2" walls. For larger pieces 5/8" to 3/4" may be necessary.

Urn is 12", 5" 3/4" wide and the base is 4". I hollowed it about 8" deep and left the bottom full thickness expecting to have it split. After soaking in alcohol and wrapping with paper the dried with no problems and I beat myself to death hollowing the last couple inches of dry wood. Do yourself a favor and turn green end grain.

Dave Smith

Turning them green in Longview, WA.


img

Re: Hollow form stock ?

#6

George Balock

Re: Turn green and soak in alcohol. PIC

George Balock

>Pete,

Do a search on this site. There was a thread a while ago with a post by Wally Dickerman about truning grenn hollow forms. I have done the twice turned method that I also use for bowls. Because the hollow form isn't cross grain it doesn't distort much.

George

Re: Hollow form stock ?

#7

Thanx much for the wisdom........! !

Pete in Holland, MI

>

Re: Hollow form stock ?

#8

Brad Vietje

I Agree With Mark & Molly

Brad Vietje

>Pete,

You probably don't want to turn big, dry chunks. First, you may never see a big block (say 10 x 10 x 12) of dry hardwood that isn't all cracked to hell. They would also take a real long time to dry. If you ever find one, when you go to turn it, it will beat you up to hollow it, and you may wish you had picked a fight with the football team instead. ;^)

The chorus is singing loudly: hollow 'em green, and dry 'em slow and steady. If you want the end result perfectly round, re-mount and true up after the wood dries. End grain H.F.'s can be left pretty thin, while side grain H.F.'s will warp more, so leave them thicker, so you'll have enough wood left to true them up inside and out.

Safe Spinning,

Brad Vietje

Thetford, VT