Home Articles Forums Gallery Marketplace Videos

WoodCentral Forums

Knowledge You Can Build On — Est. 1998

Want Better Milling & Firewood Knowledge?

cabinet scrapers

Posts

cabinet scrapers

#1

cabinet scrapers

John Lucas

>I was working on a bowl that had the pith of a limb in it. It set out in the wind all day while I was turning other bowls and it cracked. I filled the cracks with black ruberized epoxy. This can be a problem because CA glue is much harder than the wood and if you try to sand it smooth you will end up with a nasty lump.

The easiest way to remove this that I've found is to use a cabinet scraper. I hae a curve one for the inside of bowl and a straight one for the outside. These also work well whn you need to remove some torn grain. You can easily remove the torn grain and then feather out this area to blend it in with the curve of the bowl.

On green wood you can use a cabinet scraper to gt rid of tool marks. I use it while the wood is spinning but slow the lathe down to keep from heating up cabinet scraper.

Re: cabinet scrapers

#2

Re: cabinet scrapers

Mark Kauder. Phenix City, AL

>You been watching me work, John?

I started using one to refine curves about a year ago, and also use it when I am applying lacquer to fill grain - faster and cleaner than sanding.

Mark

Re: cabinet scrapers

#3

Re: cabinet scrapers

JKJ in East TN

>Same here. I use them when grain tearout is a problem, as with soft wood such as cedar and buckeye. I have several curved scrapers and a new set of small curved scrapers from Highland Hdw. Just for fun, I tried making a few things using scrapers and no sandpaper. That worked well, although they could have benefited from some 400 grit in a few places.

JKJ

Re: cabinet scrapers

#4

Ric Taylor

Re: cabinet scrapers

Ric Taylor

>John,

CA glue gets harder as the curing process continues. After the initial set-up and cure, it has the hardness similar to polystyrene plastic for about an hour. That's a good time to sand it, since the hardness is similar to the surrounding wood. After that, the CA gets progressively harder so that by the next day it is much more difficult to sand level with the surrounding wood.

It sounds like I should find someone to show me how to use furniture scrapers.

Ric

Re: cabinet scrapers

#5

Re: Esoteria, from the Hand Tool Forum

William Duffield, on the Cohansey

>I've been using cabinet scrapers and card scrapers for years on my flatwood and carvedwood projects, but until recently not on my turned wood projects. Then a fellow turner showed me how useful they were on turnings. This was an epiphany. I just kept asking myself, "Self, Why couldn't I have figured this out for myself?" Self had no answers.

If you want to learn how to prepare them for use, you might want to ask over on the Hand Tool Forum, but be forewarned on two issues:

First, there are card scrapers, just a flat piece of saw steel, and then there are cabinet scrapers. These are tools for holding the card scraper. A lot of the guys over there like TOOLS, especially fancy shiny ones. Some of them collect these these tools. For turning, the cabinet scrapers are NOT what you want. They are for FLAT wood. They are too complicated and not flexible enough for turning.

Second, the knuckle draggers, as a group, will not know how to apply the card scrapers to a turned surface, especially while it is still turning. So keep your questions to things like:

what kind of steel?

supply sources (commercial and recycled scrap)?

how to tune and turn a hook?

what's a burnisher?

how to shape a curved edge?

angle of attack?

how not to burn your fingers?

Unless you know a turner who uses one and can show you, the actual presentation of the scraper's edge to the turning you will have to figure out for yourself.

The results are well worth the adventure.

Re: cabinet scrapers

#6

Re: cabinet scrapers

adrien

>Funny, some 25 years ago I sent that suggestioin in to Fine Woodworking as a "tip." It was totally ignored by the editor so, since I had just started woodturning at the time, I assumed it was wrong and stopped using one. (I still qet queasy when people talk of using 4000 grit sandpaper for my bowls, while furniture makers stop at 220.)